Best Oxygen Sensor Removers
The Alltrade seven piece Master Sensor Socket Kit removes and installs oxygen sensors, oil pressure sending units and vacuum switches equipped with wires or vacuum tubes. Removes and installs oxygen sensors.
Reviews
Find Best Price at Amazon"However, like oil filters, automotive sensors and valves change like computers...fast."
"If you are a professional or looking to use a sensor socket set daily would suggest getting a higher end version, metal used in this set is a bit soft for repeated use."
"It is a little sloppy on some models of cars, probably due to there needs for the O2 sensor, or oil pressure sending unit."
"before removing sensor lubed with wd40 on two different occasions. Original sensor came out very easily, and new one comes pre lubed with anti seize compound on thread."
"I bought this to replace my lost O2 sensor socket."
"The only benefit I received from the kit was that I was able to install the new air fuel sensor with one of the pieces of the kit without any damage to the new sensor."
"Albeit the set is rather cheap and has a good assortment of sockets but the open end ones (which are the most commonly used) are of very poor quality as the socket easily stretches and open up under stress and to make things worse it fits really slopping into the sensors."
"An open ended wrench did the trick to remove the sensor though!"
Oxygen Sensor Socket | 5pc O2 Thread Chaser Install Offset Wrench Vacuum M12 M18. Set includes: 1-pc 3/8” Dr. extra deep broach socket (3-1/8” long), 1-pc 3/8” Dr. low-profile crowfoot socket wrench (1-1/4” long), 1-pc 1/2” Dr. offset crowfoot socket wrench (1-15/16” long), 1-pc M18 x 1.5mm and 1-pc M12 x 1.25mm thread chasers with 3/8” drive to clean and repair damaged threads.
Reviews
Find Best Price at Amazon"I ordered this set and another cool looking tool at the same time : O2 Oxygen Sensor Flexible Double Sided Head Wrench Removes & Installs Auto Tools by Neiko. https://www.amazon.com/gp/product/B01FOQJZLY. The above ^^ Neiko item ^^ was 100% useless due to the item not fitting the wrench-faces or points of them either [too tight, won't go on]. Then I reached for this Tooluxe 20764L kit, WoW!"
"I recommend this if you're looking for a low cost set of o2 sockets with the bonus of a thread chaser and convenient carrying case."
"The full socket is 3/8 square drive, and is too short and the slot is too narrow for the Bosch oxygen sensor I was installing: Looked like it would be real easy to damage the sensor's connector cable."
"I don't think I could have removed the old sensor without this tool kit."
"Worked great for changing the Bank 1 Sensor 1 on my 2008 Chevy 1500."
"I needed an offset for the down stream sensor and used the standard socket with a slit for the upstream sensor."
"If you live in an area where there is no salt exposure e.g. where they salt the roads to melt snow and ice or near a saltwater coastal area, these might be o-k for you."
"The sockets worked well for removing the o2 sensor, however if you have treads that are in need for cleaning out these thread chasers will not get the job done."
BUT With this 3 Pc Upstream socket set you’ll be able to remove & install hex vacuum switches & O2 sensors on almost every vehicle easily. The hardest part of changing an O2 sensor is removing the old sensor, but with this Ram-Pro tool the sensor will get out easily. Removes even rusted sensors. Great tight fit. Outstanding Performance. Convenient Storage. Includes Instructions. Comes in a nice case to keep the 3 sockets together. Super tool to have if you do your own auto work. Saves hundreds of dollars by doing the change yourself. Socket selection will make sensor removals painless. You may not need it for some time, but when you do, this is really handy. A must have for DIY mechanics. DESIGN: Features a 6-point beveled nose design to grip sensor fasteners securely, preventing damage to the sensor, and a wire gate that slips the socket onto the sensor easily, preventing damage to the wires.
Reviews
Find Best Price at Amazon"This is a great set."
"After using my Diagnostic Code Reader, I discovered that I needed to replace my oxygen sensors."
"Perfect fit, angled handle was just what I needed to gain access to the O2 sensor on my vehicle."
"Bought the 3-piece kit to change a failed 02 sensor on my Jeep."
"While they look efficient, I could not get them to work."
"Used to replace the air-fuel ratio sensors on a 2001 Lexus RX300 -- Bank 2 Sensor 1 and Bank 1 Sensor 1."
"Satisfied:fast delivery and item as it described."
"The kit could be designed better however so could the placement of the car's OBD sensors."
Best Oil System Tools
The spill-free funnel has been improved by adding an extra 45 degree elbow, a 5 inch extension, and a new E-adapter. The spill-free funnel eliminates trapped air pockets which usually cause erratic cooling system and heater performance.
Reviews
Find Best Price at Amazon"My 350z has a closed coolant system not like my older GM vehicles where just leaving the radiator cap open would burp the air out. of the cooling system. How to do it: From all my reading the best way to tackle this issue is to attach the funnel to your radiator cap opening while cold and fill the funnel about 1/4 up so when system burps fluid falls into they system rather than more air. Once car is cooled down follow the instructions on how to remove the funnel. and close your radiator, by this point 95-100% of the air is out of the system."
"During cooling system bleeding, the funnel serves as a reservoir for additional coolant that drains into the radiator as trapped air escapes. Anyone with a modicum of ingenuity and mechanical aptitude should be able to fabricate a custom adapter from a spare radiator cap and miscellaneous parts purchased from the plumbing department of Home Depot!"
"I don't know how I would've done a three-time coolant flush so easily (and mess free) without this thing!"
"Saw one of my co workers had something similar to this but his lacked a lot of the adapters that this one comes with and I have to say this little kit makes life a lot easier especially with the plug and i like that it comes with a top lid for storing all the adapters after the bag is torn open."
"I wish I had purchased this a long time ago."
"This made refilling the coolant a totally mess-free process and insured I had completely removed all the air bubbles from my cooling system. This is especially important with our newer lean-burning engines that have very thin cooling jackets in the engine and must have adequate coolant flow without air pockets to be effective."
"And any remaining coolant is held in the funnel when the stopper is put into place."
Best Brake Repair Tools
Made in the USA, Lang Tools (279) Brake Caliper Press allows you to work on various single, dual and quad piston calipers. Centrally located ratchet evenly spreads force in a parallel manner to prevent misalignment of pistons.
Reviews
Find Best Price at Amazon"It's way easier than using the old pad and a pair of channel locks, and is the proper type of tool to use for compressing the piston anyway."
"It makes resetting the piston so easy, much better than a block of wood and a C clamp."
"Works great."
"Such a simple tool and a great idea!...arrived yesterday and I was using it today."
"Works like it is supposed to."
"Cheap alternative to the tool trucks tool that's the same thing."
"Works great to press in caliper pistons."
"I wish I had this tool years ago."
Best Body Repair Tools
Good for 40 hours of light solvent filtering work and 8 hours of concentrated solvent filtering.
Reviews
Find Best Price at Amazon"Used this for 10+ hours while painting a car."
"Used when I was installing fiberglass insulation in my basement."
"Used these when sealing my deck."
"Simply great for home use."
"Overall good but I wish the head straps where better quality."
"It is a useful tool when around toxic vapors."
"Works great and price is a bargain."
"I noticed it stopped filtering extremely quickly though."
Best Hose Repair Kits
Whatever the job, ARES believes your tools should last a lifetime. INCLUDES: This 4pc set includes a large hook pick, straight pick, 90 degree pick and a combination pick. QUALITY: Our 4pc hook and pick set features Chrome Vanadium Steel shafts for enhanced strength and durability.
Reviews
Find Best Price at Amazon"Very good product with a nice finish."
"Ares tools have never let me down, so when I saw these I thought they would be a great addition to my garage tool collection. I own several other Ares tools and I have been very happy with all of them so I don't expect any issues."
"BIGGER than I expected, but solid."
"High, high quality picks - larger than I expected."
"these are a lot bigger than you think they are."
"High quality and larger then I expected."
Best Riveters
Patented structure increases power and reduces shock Shorter handle with double compound hinges that maximize leverage Includes Hand Nut/Thread Setting Riveter 6 interchangeable mandrel/nosepiece sets in Metric M5, M6, & M8 and in SAE 10-24, 1/4-20, & 5/16-18 Includes 10 pieces of each of the following rivet nuts: M5, M6, M8,10-24, 1/4-20 and 5/16-18 Versatile and powerful hand nut/thread setting riveter, takes the hard work out of setting rivet nuts Ideal for working in hard-to-reach area Ergonomic grip for easy operation. Includes 10 pieces of each of the following rivet nuts: M5, M6, M8,10-24, 1/4-20 and 5/16-18.
Reviews
Find Best Price at Amazon"I finally decided to give the Astro kit a try, recognizing that it's Chinese made and might have some issues. A drop of heavy oil at each pivot point, and a little light grease on the sliding quill that holds the mandrels makes all the difference in the world. This is due to the fact that the bore through the tool body is at least 1/16 larger diameter than the "pulling bar" that slides through it."
"There were open holes that were missing the flush mount rivets so by using this tool we were able to use the proper insert and install it with this riveter and then install the screw in bolt as needed. Then open your tool so the arms are wide and insert that end into the hole and compress the tool using equal strength and straight on, do not try and insert at an angle."
"Make sure you press evenly and you can compensate one side to the other need be. Adapters switch out VERY easily which is great."
"When installing the rivet just start out by only partially threading on the rivet for the first crimp then adjust how far the threads are in the rivet for the final crimp."
"I recommend before using this for the first time thread up some sacrificial rivet nuts and squeeze the tool to watch and get used to what happens when you operate the tool."
"Wish it had additional fittings for smaller riv/pim nuts, but it has performed well thus far (at least 50 times)."
"Tool worked great - take care to read the instructions and oil the tool before use."
"Get about 5 inserts each."
Best Strut Compressors
This OEMTOOLS Strut Spring Compressor quickly and safely compresses the spring for easy replacement of the strut cartridge or strut assembly repair. This OEMTOOLS Strut Spring Compressor quickly and safely compresses the spring for easy replacement of the strut cartridge or strut assembly repair. WIDE RANGE OF COMPATIBILITY: Compress Most Sizes Of Macpherson Strut Springs With The Oemtools Strut Spring Compressor – Quickly And Safely Compress The Spring For Easy Replacement Of The Strut Cartridge Or Strut Assembly Repair.
Reviews
Find Best Price at Amazon"Four also provides a greater sense of security than only using two--as I tightened, I was wondering what would happen if one of the compressors suddenly broke (when I was only using two) and what could I do--can't run since there would be no chance, and with it being also so close to my lap, would I get killed or seriously injured, or wind up speaking in a shrill tone of voice? A spring with coils almost as thick as a figure under compression is as, if not more, dangerous than a loaded gun--imagine being hit with one when a compressor breaks."
"As simple as replacing a spring or strut change can be you don't want to make a mistake when working with loaded springs."
"I would advise spending the few extra bucks and buy this in the blow molded case, the plastic that it ships in when you opt for no case is a pain and on top of it, you don't have a case!"
"It wasn't quite able to fit around my 5/8" shock, but if you remove the pin completely, you can attack it to the shock and then reinsert & secure the pin."
"You must keep the strut compressor pulled outward, near the adjustment head, in order to maintain socket access."
"Very good buy and worked for me on my utv shocks to make it easier to change ride height/turn down the spring collars."
"These worked great for my rear springs, easy to use and I felt safe as long as I used them properly and as instructed."
"If you've ever had a spring pop out of a cheaper spring compressor, you know that it's something you don't ever want to have happen again. If these can handle 18kg/mm under heavy compression, with no problem, they will easily handle the factory spring rates found in most cars (3-7kg/mm, or 170-400 lb/in), and the spring rates of off the shelf performance springs (usually no more than 35% stiffer than OEM spring rates)."
Best Fuel System Tools
With this amazing inflator,you won't need to spend any more money at the air pump at a service station!The pump is rechargeable so it is always ready when you need it,if it is depleted you can plug it in and use it too.It comes with an internal battery for use on the go and it has AC/DC adapter,charging cord as well for when you are at home or in the car. ●Pls connect the inflator with car charger instead of connecting with the wall socket while pumping something,because the output of wall socket can't reach the current required when the inflator works. The output airflow volume is about 12LPM, if tire is big, the working time will be longer. ●Flat tire emergency inflator-rechargeable lithium battery,can be charged with 12V car charger or 110V home charger.The inflator can fully pump a car tire in 15 minutes when you have a flat tire.
Reviews
Find Best Price at Amazon"The first time, I was concerned with the display showing a rapid climb in numbers. Turns out the display during that phase is counting seconds - how long it takes to complete, and not air pressure. Update: The numbers can be cycled to show elapsed time or current inflation reading. I inflated two tires on a hand truck / dolly and two bicycles which were completely flat. The charge gave up the ghost on the fourth bicycle tire. So much easier than carting stuff to a gas station or pumping by hand."
"I thought about using this "portable" device to inflate my motorbike too, but the extra step of bringing my bike to my car, and see ^^ above ^^ dissuaded me. I considered getting an AC to DC power supply, then I could just bring the "portable" inflator to the house and use an outlet. A decent AC to DC power supply capable of outputting 15A would have cost at least $50. I guess I could have used my bicycle floor pump, but the sweat effort I once exerted trying to top off a single car tire quickly dissuaded me. This can be fixed by purchasing a Topeak Pressure-Rite adapter, which has a check valve built in. I also bought a 6 foot air hose extension, because I don't like squatting by each tire as it's filling. The buttons are small, spaced closely, and have a long throw. This made it a little difficult to press, so I resorted to using my finger nails to get the proper reach I am sure the plastic will wear out with my hard finger nails pressing into it."
"I love the portability and for quick inflation needs."
"Takes getting used to but when you do."
"Very good support when contacted through email."
"Works great..took about one charge to inflate a car tire...but it worked."
"I recently purchased bikes for the family, and also had a slow leak in a car tire (not to mention having pool floats), so it seemed like a good time to buy some sort of air compressor to help solve current and future problems."
"Only good for occasional use."
Best Steering & Suspension Tools
In. POWERMODE. (L configuration), LUGSTRONG. gives you 200% more torque than any other lug wrench tire iron on the market! GUARANTEED FOR LIFE- We designed LugStrong to be the last wheel lug wrench you ever need to own.
Reviews
Find Best Price at Amazon"Very flexible with different lug options, and if you need it, it has a 1/2" drive socket for any other socket."
"Bought to go into a 1966 Ford Galaxie with new tires and custom lug nuts, so required thin walled wrench."
"The way this lug wrench folds down is awesome."
"The 1/2" socket adapter stores on the end of the silver crossbar, so make sure it doesn't drop unseen to the ground when assembling the wrench at night."
"I'd like to counter one piece of feedback another reviewer made about the leverage you can attain with this device as the product picture is deceiving (in this case in your favor)."
"I think it is a very useful tool and have ordered two more units to give as gifts this Christmas."
"definitely better than the one the came with the car - fit lugs perfectly."
"I bought this lug wrench for my wife when I was deployed and she had to use our tools to remove a trailer tire because the lug wrench from our truck did not fit the trailer lugs."
Best Tool Sets
What's in the Box Tap and Die ratcheting "T" wrench; small tap adapter; medium tap adapter; die adapter; sliding "T" for adapters; 34 taps; 34 dies, SAE and metric screw pitch gauge; #5 screwdriver; blow mold case. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Numbered coarse sizes are: 4x40, 6x32, 8x32, 10x24, 12x24, Numbered fine size is: 10x32, Inch coarse sizes are: 1/4x20, 5/16x18, 3/8x16, 7/16x14, 1/2x13. Inch fine sizes are: 1/4x28, 5/16x24, 3/8x24, 7/16x20, 1/2x20. Metric coarse sizes are: 3x0.5, 3x0.6, 4x0.7, 4x0.75, 5x0.8, 5x0.9, 6x1, 7x1, 8x1.25, 9x1.25, 10x1.5, 11x1.5, 12x1.75. Metric fine sizes are: 9x1, 10x1.25, 12x1.5. Pipe coarse size is: 1/8x27 NPT. Pipe fine size is: 1/8x28 BSP."
"We ordered this set as a gift for our son who works on cars a lot and mentioned needing something like this."
"Used on brake system of my car,To clean up treads.Handle works great and makes it real easy to thread and Other things."
"Tapped the steel cradle frame in my car for 2 bolts."
"Great tool specially the handle, it's a wratchet very clever."
"I have never had luck getting the taps I wanted and the quality I was looking for in a set until now."
"Great product - as is the case with all GearWrench tools."
"The best kit I have been exposed to."
Best Engine Tools
Additional features include: detachable leads with inductive pickup, protective hand guard for one-hand operation and patented skip circuitry test up to 9,990 RPM. Check timing, diagnose a no-spark condition, check for electronic advance/retard and more.
Reviews
Find Best Price at Amazon"Great timing light for the money, handy for the situations where there is only a single mark on the balancer and the timing cover and no other timing marks, I was able to set the gun to 8º BTDC and just line up the 2 marks on my boat engine since there was no timing tab on the timing cover."
"Good quality Timing Light."
"Needed a timing light with a tach as my 72 Scout does not have one."
"The price was great and the shipping was fast."
"Packaged well, arrived quickly, works well -- thank you!"
"Some models of this light incorporate a tach, but not this one."
"The tach and battery voltage make it easy to get everything taken care of for a tuneup."
"To eliminate the spark plug as the problem as their website implies, I used my old Actron timing light from 1993 (doesn't have the timing degrees or rpm) which works like a champ. I also picked up a Harbor Freight Xenon Timing Light this holiday season which includes timing degree adjustment and it also works fine with my ignition. I then tried the Harbor Freight harness with the 3568 timing light and for about 15 seconds it was working, but then the flashing went erratic. For example the Craftsman Digital timing light controls and wire harness is a dead ringer for the Actron digital timing light and the Matco timing light looks like a dead ringer of the Innova 5568."
Best Parts Washers
This 20 gallon parts washer with a 12 gallon solvent capacity can clean small to medium size parts quickly. Max pump output: 192 gph flow rate (w/ flexible pipe); max pump output: 318 gph flow rate (w/o flexible pipe); recirculates 2.6-3.2 gpm of solvent.
Reviews
Find Best Price at Amazon"The under tray is a great place to set a part for draining, and the catch basin makes draining the main basin a snap (but be aware the catch basin only holds about a gallon of liquid at once) and the drain plug is a serious metal piece."
"The product's instructions limit the unit's use to water based cleaner and, even then, non-chloride based. The unit I received has numerous missed spots, large run areas and paint flaked off when tightening bolts on assembly. If you're mechanically inclined, the unit has few parts and goes together quite easily."
"This is a nice little wash tank for the price."
"We use this device in a fire station where we have to constantly clean and maintain our chainsaws."
"easy setup ."
"Very nice addition to my shop ...I love that it is on casters ...very solid and moves easily..works very well..very happy!"
"Very good quality and worked as stated."
Best Pullers
The OTC 9-way slide hammer puller set pulls flange-type rear axles and most front-wheel drive hubs and the internal and external jaws provide a variety of combinations to pull bearings, gears and seals. Includes a grip wrench adapter and a dent puller attachment for sheet metal or other unique pulling requirements.
Reviews
Find Best Price at Amazon"This was Ideal for what I needed, Had a stubborn wheel bearing and worked our great."
"Well made quality product."
"This presses out the bearing and allows you to press in the new bearing without ever removing the steering knuckle form the car."
"This is one fantastic tool !"
"This was purchased to use in an automotive shop."
"Nice set......fixed my broken front wheel lug studs the right way on my 08 Honda odyssey after One of the big tire chain shops ran them on with an impact gun instead of using a torque wrench like an experienced tech would."
"great set, worked perfect for pulling the hub assembly off my wifes van."
"Pretty nice kit, well built."
Best Thread Repair Kits
Sav-a-thread complete kit, can be used to repair both taper seat & gasket type spark plug assemblies, 3 insert lengths to accommodates all reaches, positive mechanical locking feature means the insert will never come out, piloted reamer tap means no drilling is necessary & perfect alignment of the tapped hole. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"This worked fantastic for my 2000 Suzuki Hayabusa to repair my stripped oil pain drain plug threads."
"Changing out spark plugs on my 2001 Honda civic got to number 3 cylinder on it started to get super thight and you could feel the threads starting to strip I thightened it back in so I could still drive it until I had the money to fix ( time sert kits are expensive over $200 for the kit) then I found this kit ordered it and worked great only took about an hour with a few beers while doing the job."
"Seems to be holding though, and allows you to use the original spark plug style, unlike one of the other repair kits that forces you to change to the "long reach" style plug, which could cause a check engine light."
"This product is amazing it literally took me 20 minutes to fix my F 150."
"Make sure you out a ton of grease on the tap to catch all the aluminum shavings, then I used a thin metal rod with q tips taped to it so I could reach down in the spark plug "valley" to pull up any loose shavings."
"I used it on my '84 toyota pickup (22r), and I really disliked cutting into that aluminum head but it seemed to go ok. I managed to hit the piston while I was threading (hand smacks forehead) so make sure you either don't get all cavalier with your wrenchin' or ensure your piston is out of the way."
"I used this to fix my stripped threads on my 2005 Ford Crown Victoria."
"cb360 blew a plug and I bought this to replace it."
Best Brake Tools
European Power Bleeder Power Bleeder- pressure brake bleeder, 2 quart capacity, with 45mm threaded adapter (1100) for most European cars including Audi, BMW, Mercedes, Porsche, Saab, Volvo, VW and others. Motive POWER BLEEDER hand pump works anywhere - great for the home, shop, or track.
Reviews
Find Best Price at Amazon"I happened to mess up on the initial purchase, se la vi, but the second item, I didn't know about until mine started spraying and every time I cut an inch off to get past a crack in the line, a new one appeared."
"Took me longer to fill it with brake fluid and pump it up than it did to actually bleed my clutch!"
"Works excellent, turns bleeding the brakes or clutch into a one man job, very well constructed nice thick tubing and tank material."
"My car required 2 bar (30 PSI) to bleed the brakes per the service manual and this worked fine at that high a pressure."
"Best work around to get the black model effect is to hold the cap that goes on brake fluid reservoir tightly and rotate empty brake pump bottle (I think it's clockwise) to two turns holding the bottle tight, put the cap on the reservoir holding the bottle tight after the turn, the pipe will unwind as the cap is rotated on the reservoir."
"I filled up the bleeder with 5 cans and screwed the adapter onto the master cylinder -- perfect fit. I don't think the Black Label bleeder is necessary as the plastic adapter on this one that screws onto the master cylinder seems sturdy enough."
"Update : Solved the kinky hose problem by adapting the 1/4" quick disconnect adapter from Harbor Freight. Its a pity that the bleeder cap already has the threading for it and all it needs is the disconnect adapter which the bleeder does not have, which when using it resulted in a big frustration with the kinky hose. I should further mention that for those bleeder without the air release valve, it is prudent to loosen the cap a bit to let the air out before disconnecting from the quick-disconnect."
Best Tool Boxes
Patented tiered cantilever multi-level rolling system allows easy access to all 4 storage areas at the same time.
Reviews
Find Best Price at Amazon"Instead my intent was to use it for organizing camping gear. Now it supports my camp stove for cooking!"
"I use this for a Kitchen CHUCK BOX that can be used when we go camping, or in times of emergency and it works great!"
"great item I am using them to separate different types of items used for different jobs like wood working items in 1 and plumbing fitting in another and electric supplies in another ex."
"Wonderful for portable maintenance tools."
"I bought it for camping."
"Love this for my direct sales business."
"This was a great product and came fast."
Best Garage & Shop Products
It handles both wet and dry pickup, includes all accessories needed for complete interior cleaning and easily converts to a blower to dry motorcycles, car grills and wheels. Other great features include a 10-foot cord with wrap, 6-foot, 1.25-inch hose, reusable cloth filter, reusable foam sleeve, 2-in-1 utility nozzle, crevice tool, deluxe car nozzle, blower nozzle, and detail brush. 2.5 gallon storage tank and 2 horsepower motor with an auto shut-off to prevent overflow.
Reviews
Find Best Price at Amazon"Before getting this product I would go downtown to one of those car wash places and poke an endless supply of quarters into a bulky commercial vacuum cleaner. This has never been a pleasant experience since the car wash vacuum cleaners always seem to come with large barely-flexible, cumbersome hoses equipped with an over-wide nozzle ill-suited to clean the hard-to-reach places in your car."
"However, I seriously don't have the space for a large shop vac so the compact size of this is so great yet it performs as strongly as the large sizes. One typically runs and hides while the other follows me around barking madly at it--but with this little shop vac they even kept coming up to it while I'm using it with no barking. So I promptly turned off the water, changed the filter from the cloth to the water filter in this little vac and proceeded to test its wet suction! I haven't tried the wet part yet or the "blow" part either but if the suction works this well, then I'm sure I'll have no worries."
"NOTE: for fireplace ashes and drywall dust, which are extremely fine, the manufacturer recommends an optional fine filter, and this is important, as the powdery dust from ashes will work through a regular filter and burn out the motor. If you do (and I did) hardly any ash gets through to the filter over the motor, and you can simply remove the bag and drop it in the garbage instead of turning the canister over and dumping the ashes in a choking cloud of dust."
"The little notches in the top for the attachments make this vacuume cleaner difficult to handle and store."
"It also comes with an attachment to clean the car's air vents as they can become dusty."
"I got this to keep in the basement for picking up spilled cat litter and various debris from my small workshop."
"I was tired of dragging in the big ol' shop vac when I needed it."
"It's not the best shop vac ever, of course, but for a small one and a cheap one, it vacuums well and should last a long time."
Best Measuring Tools
Correctly tightening fasteners to a vehicle or equipment manufacturer's torque specifications ensures parts are properly secured without being damaged. When the preset torque value is reached, a reliable mechanical operation inside the handle produces a click you can hear and feel, alerting you to stop applying force. Built for consistent performance and years of dependable service, the mechanical design doesn't need batteries, and the allsteel construction has no plastic parts to break or wear out. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Now, that may be great for lugs and such but there are some really hard to get to spots on my car that require greater than 100lb torque specks (one I know off the top of my head is 146 ft lbs)."
"Only used it for a little while but so far so good."
"I regularly use it at the higher torque settings and it works great and is easy to use, see, and adjust."
"This is a really good wrench. I just did the job this week and used this to tighten the axle bolt to 140 lbs."
"One of the two retaining bolts at the head of the wrench fell out the first time I used it."
"This thing is one serious wrench."
"Good enough for what I need it for, which is primarily torquing lugnuts."
"LOVE this thing!!!"
Best Hand Tools
Drive Click Torque Wrench lets you work with confidence, eliminating guessing and the common tendency to overtighten fasteners. Simple and easy to use, this wrench has a reversible ratcheting head that drives fasteners in both directions and measures torque in the clockwise direction. drive torque wrench (1) Storage case (1) Operator's manual with torque conversion chart. Wrench emits a click that can be heard and felt when the preset value is reached.
Reviews
Find Best Price at Amazon"Update 9/18/2015. I got my replacement yesterday and I'm really satisfied on how Russ from Tekton took care of this, I asked how to return the other original item and instead let me hang on to it."
"I asked a local mechanic to verify that the tool was working - he said it seemed fine, but I cannot get it to click at all when using it set to 108 ft-lb (well within it's specified range) to torque the axel nut on my motorcycle. When talking with them on the phone, the manufacturer admitted that this type of torque wrench has a design flaw which makes it easy to inadvertently break the tool: The instructions are clear that the tool must be stored at it's lowest setting. But if you loosen the tool to just BELOW it's lowest setting, (which the design of the tool makes far too easy to do), it is permanently damaged."
"This 1/2 inch drive socket torque wrench is ideal for that 13 to almost 203 Newton Meters (Nm) range that applies to larger fasteners on a mountain bike (such as the bottom bracket and freewheel), and to make sure undue stress is not being applied to the carbon fiber frame or components. (you have to consider dynamic versus static loading when conducting testing) Still, a deviance of only 0.8% is well within the 4% Tekton claims and is very accurate for a torque wrench in this price range. Also, the feel of the Tekton 24335 is much more intuitive during dynamic loading and when you reach the limit in torque you set, the click and swivel of the head is sharp, loud and easy to notice due to the roller pin rolling over the roller bearing. That is simply a huge amount of difference and when you combine that with the fact that the Tekton 24335 is so accurate, it makes choosing the Tekton easy. So far, I have had my Tekton 24335 for about seven months and have used it not only on my bikes but also with some light auto work, and the wrench has been both accurate and performed superbly."
"The adjusting mechanism was very rough, and when adjusting to the upper end of the range, difficult."
"Broke after just a few uses.Weird grinding noises when changing torque setting, and no longer clicks when torque setting is reached."
Best Applicator Tools
The minus (-) sign indicates less water (so more foam is produced), and the (+) indicates more water (so less foam is produced). ☆Variable, adjustable spray nozzle for accurate mixing and foam generation.Turn the top knob right / closed to get the thickest mixture, adjust the nozzle to get a proper spray pattern, and let it loose.
Reviews
Find Best Price at Amazon"Pink for car soap and only need to fill this about 3/4 of the way with water to wash my large SUV and even less if I'm doing a sedan."
"Don't waste your money on any of those name brand foamers."
"Great product for cost, easy to use."
"This is a great addition to the truck cleaning tools I have and I may even bring this to the fire station from time to time."
"Car wash can be expensive sometimes, especially if you ran into those ones that cost you 15 dollars and the car came out just like you can even do it yourself."
"If my cars are not that dirty it will wash 2 with one fill or wash my dirt bike 2 times."
"I dropped it a few times bc I’m clumsy and it didn’t break or chip or anything, so definitely quality."
"I would recommend this to anybody who washes their own car and has a small pressure washer."
Best Bushing Tools
Easy to Use. To use, simply select the correct bushing, align straight and centered, and then pound in/out. Practical: The ABN Bearing Race and Seal Bush Driver Set with Carrying Case – Master / Universal Kit for Automotive Wheel Bearings allows for easy race seal installation without damaging the axle housing.
Reviews
Find Best Price at Amazon"Worked great for driving an axle seal into the rear housing."
"The tool set worked well."
"this was a great purchase that saved me some time and money and the product works as described."
"Nice driver set."
"Easy to install seals with this kit."
"This is a great product and it exceeded my expectations I would suggest for anyone who needs a product like this to buy it I'm very happy with it."
"Seems like a nice set."
"It makes seating bearing races more accurate and easier."
Best Flywheel Locks
This kit consists of adequate tools to lock the camshafts on twin cam (multi-valve) engines in order to stop them rotating out of timed position when the timing belt is replaced and removed. Included. x10 Camshaft locking tool. x4 camshaft locking pins. Setting and locking plate. Balancer pin. TDC locking pin. x2 popular flywheel holding tools. This kit consists of adequate tools to lock the camshafts on twin cam (multi-valve) engines in order to stop them rotating out of timed position when the timing belt is replaced and removed.
Find Best Price at AmazonBest Electrical System Tools
The 10 MegOhm input is safe for automotive and household uses (i.e., household outlets, fuses, wiring, general-purpose batteries, vehicle battery and charging system, automotive circuits and more). Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"I'll admit I'm not a power user, my job doesn't depend on this unit or anything but for checking circuits in the house, finding shorts in the truck wiring, debugging the well pump, checking resister values (because I'm too old to see the damn color codes), probing Arduino circuits, etc it's been just the ticket."
"Also, this meter does not abide by E/IR rules, a tad off, so if you really need accurate measurements, this meter is not the right one."
"Worked awesome till all my tools got stolen out of my work truck which the lame ass insurance of my employer at the time wouldn't cover."
"I’ve been using an old cheapo Radio Shack multimeter for years but it’s been getting harder to see while working."
"I've had mine for over 2 years now and love it."
"This is a quality product and very accurate."
"Awesome product bought to test my battery, works great!!"
"Used it several times around the house and when working on the car then went several months without using it and it was dead."
Best Diagnostic & Test Tools
is left behind by the other wireless and handheld code readers. All GM brands, including Chevrolet, GMC, Cadillac, Buick, Saab, Saturn, Pontiac, Oldsmobile, & Hummer All Ford brands , including Ford, Lincoln, & Mercury All Chrysler brands , including Chrysler, Dodge, Jeep, Ram, Plymouth, Fiat, & Alfa Romeo All Toyota brands , including Toyota, Lexus, & Scion All Nissan brands , including Nissan, Infiniti, & Renault All BMW brands sold in North America , including BMW, Mini & Rolls Royce All Honda brands sold in North America , including Honda & Acura (2003 models and newer) All Volkswagen brands sold in North America , including Volkswagen, Audi, Lamborghini & Bentley. As easy to use as a code reader with all the capabilities of an expensive handheld scan tool, plus the benefits of your smartphone or tablet (free app updates, portability, saving data, interactive graphing of live data).
Reviews
Find Best Price at Amazon"This app imo is awesome 1st I am a used car dealer I need a fast OBII that is accurate and that can do a basic scan of all vehicle to make sure the car can pass emissions and to check for trouble codes or pending codes when a check engine is not on. Except I noticed on this bad boy I can see when the last codes where erased on a vehicle so I can weed out those dealer cars that clear codes on their problem child cars as they enter the auction. It goes to auctions 4 auctions a week and probably scans at least 50 cars per auction. I can scan vehicle almost on the auction block if need be for those cars that just appear that you never saw parked in the sale lot.. Also for kicks i scanned a Maserati and it worked..Scans Mercedes c class to."
"Personally I do not like this it seems that now you are forced to buy all the extras in the app since you are paying $99 for the Adapter, I have 4 other OBD2 Bluetooth adapters that work with torque and other apps and provide very similar information, BlueDriver is more advanced being able to Read/Clear Enhanced Codes (e.g. ABS, Airbag, Transmission, etc.)."
"I leave the module plugged into the OBD2 port on my 2011 Mercedes GL350 (Diesel) constantly since I purchased the BlueDriver in June, 2017. I am towing the trailer again this week with the real-time logging running, when yesterday, on hwy 93 in Idaho, the middle of nowhere, the engine dies! We miraculously find a place to safely pull off the 2-lane (no shoulder) highway and my wife starts calling our subscription towing service, I look at the BlueDriver app now that we are stopped, and I can now see a warning that the fuel pressure is low. My wife re-starts the car, no leak, so we put on the pretty cover, cleaned up with simple green and a paper towel, and head down the road."
Best Drive Train Tools
The OTC 4972 is for solid holding of drive clutch for spider removal when shimming for belt-to-sheave clearance or servicing spider. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Worked GREAT!"
"Worked just as described, on my 2009 Polaris RZR 800 Clutch."
"Must have tool for taking apart Polaris clutches."
"Works great."
"Doesn't work with clutches with starter flywheel."
"Quality made."
Best Muffler Tools
This unit is high performance maintenance tool which is paricularly suitable for use in machine noise detector.By using it, you can easily detect and find the early hidden trouble of a machine so that you can service the machine in an early time to ensure the machine's proper operation and avoid any damage and economic loss. Detecting noise in engine, bearings, motors, chassis, transmissions and other parts.Suitable for autos, ships, aircraft, machine tools and other mechanical equipment.
Reviews
Find Best Price at Amazon"I bought it for my husband for Christmas my husband Loveit ,we saved alat of money and a car,Look great and Work great."
Best Jump Starters & Battery Chargers
Battery Tender Junior 12V Battery Charger is much more than a trickle charger. Automatic charge cycle functionality switches to float mode after fully charging the battery.
Reviews
Find Best Price at Amazon"There are quite a few float charger type products out there that bill themselves as "battery tenders" but the actual product name of this is "Battery Tender Jr." - they have other Battery Tender products, including one with higher charging output, and one with more outputs for charging multiple batteries. A battery that is kept at full charge will have a much longer service life than a battery that is left sitting with less than a full charge. The difference with the Battery Tender products is that they are intelligent: they have computers inside that analyze the state of charge of the battery to which they are connected, and alter their output to adjust: Initialization, Bulk Charge Mode, Absorption Mode, Float Mode). I have not had a single battery go bad in the five years since I have started using Battery Tenders - and every battery still performs like it is brand new. When I park the bike, I simply flip open the cubby, plug in the Battery Tender, and I know the battery is protected and maintained. The Battery Tender works great on standard flooded wet-cell lead-acid batteries, as well as AGM (absorption glass mat) batteries. And you can now get accessories that plug into the Battery Tender vehicle-side connector when the Battery Tender is not connected. See more about these accessories here: Battery Tender USB Charger and 12 volt Socket. Overall, this is one of my favorite products, they work amazingly well, keep your batteries in top shape, and cost less than a quarter of the cost of a single new battery."
"Had this hooked up to my car for months to keep the battery full of life."
"This tender doesn't seem as sturdy as the Battery Tender Juniors I've purchased in the past."
"Absolutely the best way to keep your batteries topped off during very cold weather."
"This one is more circuitry so I'll have to wait to see how it holds up in the long run."
"Great for maintaining my atv battery between plowing and using the winch."
"Good unit for keeping a battery healthy throughout the winter."
"I checked the voltage output and found only putting out 9.01 vdc (should be over 12vdc), called customer service and they wanted to charge me a "warranty return fee" and possibly other chargers also on top of shipping charges to get the faulty product back to them.-these are less than 9 months old!"
Best Tire & Wheel Tools
This creeper seat features 360 degree rotating casters, steel construction; fully padded seat, and large tool tray. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"I am 71 years old and am laying tile on a basement floor."
"Perfect creeper seat for the garage or workshop, great for working on cars or lawnmowers…etc This creeper seat can hold up 300 lbs without any issues so it’s the perfect seat for most people."
"I can grab wood at the box, roll to the stove, feed fire, keep lighters handy in the tray, not pop my kneecaps into the next county while squatting down even further or shatter them by kneeling. I may add them, but if you're close to the stated weight capacity, it has some springy bounce to it, which may over time result in some less-springy metal fatigue, less funny snapping, and collapsing into the parts tray where the thing will shoot out from under your butt and drop you on the ground."
"It's a little lower than a low stool but not so low you cannot get up off the floor easily from a sitting position."
"I don't have a nice motorcyle lift and having to work on areas of the bike 1-3 ft above the ground is a breeze with this guy."
"For a person with physical issues, this makes life easier during setup, checking air pressure, or working in the lower storage bays."
"If you floor is very smooth this will be fine, but if it is a bit rough or you hit some small debris be prepared for a wheel to lock up."
"It appears like this metal was all rusty, and not store properly, then they tried just painting over it."
Best Cooling & Water Pump Tools
Special Features includes: Holds timing chain in place so water pump can be removed for service, special design allows easy installation regardless of timing chain orientation, simply remove access plate from front cover and install the tool, tool saves costly loss of timing on 2002–2008 GM 2.2L and 2.4L EcoTech motors found in Chevrolet, Oldsmobile, Pontiac and Saturn platforms. Tool saves costly loss of timing on 2002–2008 GM 2.2L and 2.4L EcoTech motors found in Chevrolet Oldsmobile Pontiac and Saturn platforms.
Reviews
Find Best Price at Amazon"My channel is davidmezera and the name of the video is water pump replacement on 2007 Chevy Cobalt 2.2L ecotech engine."
"Installing the tool was a bear, but that is not the tools fault, but the designers of the Chevy Cobalt!"
"An absolute "must have" tool if you're replacing a water pump on a GM ECOTEC 2.2L or 2.4L engine."
"If you drop the bolt in it may go all the way into the oil pan."
"If you use this tool make sure you tighten all the bolts."
"There are reports of whining from the water pump even if you use this tool or a similar one and even if the gear doesn't move."
"Exactly what the description says."
"this tool is quit functional."
Best Impact Wrenches
The DEWALT DCF899HB 20v MAX XR Brushless High Torque 1/2" Impact Wrench w. Hog Ring Anvil features a brushless motor which is designed to provide superior run-time, performance and durability. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"The only bolts I had issues with required me to put it on the 3rd setting, I got a little over zealous with the trigger and snapped them like they were made of plastic. Was looking at getting a air one, but didn't think my compressor would handle it and since I had about every other Dewalt 20 volt tool and 6 batteries this was a no brainer. It is heavy so holding above your head for a long time can get to your arm and shoulder, but still better than a ratchet and breaker bar."
"I have searched all around to different brands and watched videos on them for performance and what other real people are saying about the different models and names of impact wrenches. Hog ring is easier to get off and Detent Pin you need a screw driver or a specific tool. But in reality its fairly light compared to other models. I took off a Catalytic converter with bolts rusted on that I could not get with a breaker bar. I was thinking of buying the 20v 1/2" impact that isn't the high torque version but Im so glad I spent the extra $70 and got this one."
"I tried to remove some seized nuts off a car wheel."
"Bought the DEWALT DCF899HB 20V MAX XR Brushless High Torque 1/2" Impact Wrench with Hog Ring Anvil and the DEWALT DW22812 1/2-Inch 10-Piece IMPACT READY Socket Set to remove blades from a Steiner mower deck."
"If you have a seized or extremely tight bolt I suspect this gun will either liberate your fastener or snap it into pieces like an absolute champion."
"Beast!"
"I used the dewalt to remove tractor tires from a Kubota."
"most powerful impact gun available."