Best Epoxy Adhesives
Crystal Clear Bar Table Top Epoxy Resin Coating For Wood Tabletop - 1 Gallon Kit.
Reviews
Find Best Price at Amazon"(3ft by 3ft, 1/2 inch deep - with plates) I accomplished this in (2) pours, each 4 hours apart. 2) I mixed 2 gallons for 7 minutes each time and it came out awesome - don't scrape your mixing sticks when you get to the pouring part because you only want thoroughly mixed product to be poured - not remnants of either part alone that you may get if you scrape. 3) POUR PART B IN YOUR MIXING BUCKET BEFORE PART A - MIXING WILL BE SO MUCH EASIER."
"We've been using this epoxy resin to finish an outdoor coffee table and and a bathroom countertop. We are going to do our biggest project next and do our kitchen counters."
"Stir well for 5-10 min, but dont whip, should turn completely clear like water, bubbles are okay. Repeat this every 10 mins for 1 hour. Scrape epoxy from under edges and apply to any areas that may lose some from leveling."
"I had to sand down an area that bubbled up due to pouring too thick of a first coat."
"I used a high density foam roller to apply this to a painted countertop and a roller is the way to go rather than using a foam brush."
"I found this product to be easy to use and the finish extremely clear."
"Take your time, follow the instructions and this stuff will turn out GREAT."
"Bought this for s friend that was doing s job for me,"
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Automotive Brick Concrete Epoxy and Adhesives Fiberglass Metal And more Instructions. 1. Prepare: Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. Great for household repairs, automotive projects, plumbing and marine applications, crafts and more. Once cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled and will withstand temperatures of up to 550 degrees Fahrenheit.
Reviews
Find Best Price at Amazon"The major drawback to epoxies is that they consist of two parts (resin and hardener) which must be mixed in small batches, and then applied with your own applicator (e.g., a toothpick or popsicle stick). Some are packaged in a dual-syringe--but that is not an adequate solution, because the components must still be manually mixed in order harden to maximum strength. HOW TO USE JB-WELD. General Principles: Although JB WELD makes an excellent filler---and can even be used to cast small parts, it is not remotely as strong as real metal used this way. I generally use a small grinding wheel in a Dremel tool to roughen the surfaces. If you do not have a commercial degreaser handy, a paste of laundry detergent and a stiff brush may do the trick. Joining Broken Parts: If you are joining broken parts, with a clean but irregular matching surfaces, limit the roughening to scratching with a wire brush or etching with an acid (but be sure to wash off all traces of the acid). Apply a THIN uniform layer of JB WELD, lightly clamp together hard enough to squeeze out any excess. ScotchBlue Painter's Tape for Multi-Surfaces 2090-.75A, 3/4 Inches by 60 Yards, 1 Roll. Joining Dissimilar Parts: Minimize any gaps if possible, e.g., by sanding if possible so that the contact as perfect as possible. To join a 1/8" steel rod, to another 1/8" steel rod, forming a "T" (a common and easy welding job, almost impossible with just JB-Weld), cut two 1"-long "L's" from a heavy-paper clip, (or make L's from similar wire), and embed those with JB-Weld on opposite sides of the joint. You can further strenthen the joint by wrapping fine steel wire around the rods holding the "L"s in place---before covering it all with JB-Weld. For small parts, or when wire wouldn't work well, unwaxed dental floss is remarkably strong, and can do an excellent job of reinforcing joints (when embeded in JB Weld). Holes in car body panels etc: If you can cover at least one side of the hole with a piece of sheet metal (held in place by JB Weld) that is a good strategy---the combination of pop-rivets and JB Weld often works especially well, even if you ultimately sand the heads of the pop rivets away. Note that epoxies do not "dry"--there are no solvents to evaporate, instead a chemical reaction hardens the cement (a plastic resin). White glue shrinks a great deal as it dries, and so is not good for filling holes or large gaps. I've used Goop to repair ceramic plant pots, water hoses, and shoes; to seal holes in air-mattresses, to close small holes in window screens, as plumbers paste in assembling plumbing parts, to I also use it to seal rust spots on my dishwasher rack--the Goop it also makes a "cushioned" surface that will prevent scratches to dishes. It is a good alternative for Goop for general household use on glass, plastic, and metal when you do not need the maximum possible strength. For example: GE Silicone II Household Glue, 2.8 oz. Fabric Glue: Beacon Fabri-Tac Permanent Adhesive, 4-Ounce works amazingly well on fabrics, saturating the surfaces enough to provide a very strong bond, but without soaking through. It remains very flexible, e.g., it would probably be great on leather or heavy vinyl (e.g., women's handbags, shoes, luggage, etc.). Previously, I used super-glue frequently on objects (e.g., jewelry) when a clear bond was required---however, Goop is better for such applications, safer, and more conveneient. Opened super-glue keeps poorly, even in tighly sealed glass containers---so I recommended packages of multiple very small tubes. Most construction adhesives are slightly flexible, and so can even be used on leather (i.e., to repair a loose shoe sole), etc. As an adhesive, it is the weakest on this list, but is strong enough for many purposes when spread over a large surface, such as the back of a ceramic tile. I could have used construction adhesive (albeit any excess that squeezed out would have been ugly)--but caulking compound was quick, cheap, looks good, and was more than adequate for the job."
"It was likely just a bubble in the granite mix that came to the surface and remained unseen until it got to me. I didn't want to take out the sink and replace it for two reasons: one it is a lot of work and two it seems like such a waste of materials in the environmental sense. I called the company and they would replace the sink free of charge (not install)."
"This is the epoxy Honda calls for when repairing leaks in the block or heads from aluminum porosity. It is very hard and strong and will withstand 550 degrees F. The key is to clean the surface completely."
"I bought this to repair an office chair where the wheel kept falling out."
"Make sure whatever you are fixing has a clean surface free of paint and dirt and you will have a strong repair."
"I sanded the end of the support rod and sanded the broken weld spot on the main pole, then applied the J-B Weld."
"Man, this product is so strong."
"I used a small craft sponge to apply and held it together w a rubber band until cured."
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Automotive Brick Concrete Epoxy and Adhesives Fiberglass Metal And more Instructions. 1. Prepare: Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. Sets in 4-6 hours at room temperature and cures dark grey in 15-24 hours and rated at a tensile strength of 3960 PSI. Once cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled and will withstand temperatures of up to 550 degrees Fahrenheit.
Reviews
Find Best Price at Amazon"The major drawback to epoxies is that they consist of two parts (resin and hardener) which must be mixed in small batches, and then applied with your own applicator (e.g., a toothpick or popsicle stick). Some are packaged in a dual-syringe--but that is not an adequate solution, because the components must still be manually mixed in order harden to maximum strength. HOW TO USE JB-WELD. General Principles: Although JB WELD makes an excellent filler---and can even be used to cast small parts, it is not remotely as strong as real metal used this way. I generally use a small grinding wheel in a Dremel tool to roughen the surfaces. If you do not have a commercial degreaser handy, a paste of laundry detergent and a stiff brush may do the trick. Joining Broken Parts: If you are joining broken parts, with a clean but irregular matching surfaces, limit the roughening to scratching with a wire brush or etching with an acid (but be sure to wash off all traces of the acid). Apply a THIN uniform layer of JB WELD, lightly clamp together hard enough to squeeze out any excess. ScotchBlue Painter's Tape for Multi-Surfaces 2090-.75A, 3/4 Inches by 60 Yards, 1 Roll. Joining Dissimilar Parts: Minimize any gaps if possible, e.g., by sanding if possible so that the contact as perfect as possible. To join a 1/8" steel rod, to another 1/8" steel rod, forming a "T" (a common and easy welding job, almost impossible with just JB-Weld), cut two 1"-long "L's" from a heavy-paper clip, (or make L's from similar wire), and embed those with JB-Weld on opposite sides of the joint. You can further strenthen the joint by wrapping fine steel wire around the rods holding the "L"s in place---before covering it all with JB-Weld. For small parts, or when wire wouldn't work well, unwaxed dental floss is remarkably strong, and can do an excellent job of reinforcing joints (when embeded in JB Weld). Holes in car body panels etc: If you can cover at least one side of the hole with a piece of sheet metal (held in place by JB Weld) that is a good strategy---the combination of pop-rivets and JB Weld often works especially well, even if you ultimately sand the heads of the pop rivets away. Note that epoxies do not "dry"--there are no solvents to evaporate, instead a chemical reaction hardens the cement (a plastic resin). White glue shrinks a great deal as it dries, and so is not good for filling holes or large gaps. I've used Goop to repair ceramic plant pots, water hoses, and shoes; to seal holes in air-mattresses, to close small holes in window screens, as plumbers paste in assembling plumbing parts, to I also use it to seal rust spots on my dishwasher rack--the Goop it also makes a "cushioned" surface that will prevent scratches to dishes. It is a good alternative for Goop for general household use on glass, plastic, and metal when you do not need the maximum possible strength. For example: GE Silicone II Household Glue, 2.8 oz. Fabric Glue: Beacon Fabri-Tac Permanent Adhesive, 4-Ounce works amazingly well on fabrics, saturating the surfaces enough to provide a very strong bond, but without soaking through. It remains very flexible, e.g., it would probably be great on leather or heavy vinyl (e.g., women's handbags, shoes, luggage, etc.). Previously, I used super-glue frequently on objects (e.g., jewelry) when a clear bond was required---however, Goop is better for such applications, safer, and more conveneient. Opened super-glue keeps poorly, even in tighly sealed glass containers---so I recommended packages of multiple very small tubes. Most construction adhesives are slightly flexible, and so can even be used on leather (i.e., to repair a loose shoe sole), etc. As an adhesive, it is the weakest on this list, but is strong enough for many purposes when spread over a large surface, such as the back of a ceramic tile. I could have used construction adhesive (albeit any excess that squeezed out would have been ugly)--but caulking compound was quick, cheap, looks good, and was more than adequate for the job."
"It was likely just a bubble in the granite mix that came to the surface and remained unseen until it got to me. I didn't want to take out the sink and replace it for two reasons: one it is a lot of work and two it seems like such a waste of materials in the environmental sense. I called the company and they would replace the sink free of charge (not install)."
"This is the epoxy Honda calls for when repairing leaks in the block or heads from aluminum porosity. It is very hard and strong and will withstand 550 degrees F. The key is to clean the surface completely."
"I bought this to repair an office chair where the wheel kept falling out."
"Make sure whatever you are fixing has a clean surface free of paint and dirt and you will have a strong repair."
"I sanded the end of the support rod and sanded the broken weld spot on the main pole, then applied the J-B Weld."
"Man, this product is so strong."
"I used a small craft sponge to apply and held it together w a rubber band until cured."
Best Metal Filled Epoxies
Sets in 4-6 hours at room temperature and cures dark grey in 15-24 hours and rated at a tensile strength of 3960 PSI. Once cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled and will withstand temperatures of up to 550 degrees Fahrenheit.
Reviews
Find Best Price at Amazon"The major drawback to epoxies is that they consist of two parts (resin and hardener) which must be mixed in small batches, and then applied with your own applicator (e.g., a toothpick or popsicle stick). Some are packaged in a dual-syringe--but that is not an adequate solution, because the components must still be manually mixed in order harden to maximum strength. HOW TO USE JB-WELD. General Principles: Although JB WELD makes an excellent filler---and can even be used to cast small parts, it is not remotely as strong as real metal used this way. I generally use a small grinding wheel in a Dremel tool to roughen the surfaces. If you do not have a commercial degreaser handy, a paste of laundry detergent and a stiff brush may do the trick. Joining Broken Parts: If you are joining broken parts, with a clean but irregular matching surfaces, limit the roughening to scratching with a wire brush or etching with an acid (but be sure to wash off all traces of the acid). Apply a THIN uniform layer of JB WELD, lightly clamp together hard enough to squeeze out any excess. ScotchBlue Painter's Tape for Multi-Surfaces 2090-.75A, 3/4 Inches by 60 Yards, 1 Roll. Joining Dissimilar Parts: Minimize any gaps if possible, e.g., by sanding if possible so that the contact as perfect as possible. To join a 1/8" steel rod, to another 1/8" steel rod, forming a "T" (a common and easy welding job, almost impossible with just JB-Weld), cut two 1"-long "L's" from a heavy-paper clip, (or make L's from similar wire), and embed those with JB-Weld on opposite sides of the joint. You can further strenthen the joint by wrapping fine steel wire around the rods holding the "L"s in place---before covering it all with JB-Weld. For small parts, or when wire wouldn't work well, unwaxed dental floss is remarkably strong, and can do an excellent job of reinforcing joints (when embeded in JB Weld). Holes in car body panels etc: If you can cover at least one side of the hole with a piece of sheet metal (held in place by JB Weld) that is a good strategy---the combination of pop-rivets and JB Weld often works especially well, even if you ultimately sand the heads of the pop rivets away. Note that epoxies do not "dry"--there are no solvents to evaporate, instead a chemical reaction hardens the cement (a plastic resin). White glue shrinks a great deal as it dries, and so is not good for filling holes or large gaps. I've used Goop to repair ceramic plant pots, water hoses, and shoes; to seal holes in air-mattresses, to close small holes in window screens, as plumbers paste in assembling plumbing parts, to I also use it to seal rust spots on my dishwasher rack--the Goop it also makes a "cushioned" surface that will prevent scratches to dishes. It is a good alternative for Goop for general household use on glass, plastic, and metal when you do not need the maximum possible strength. For example: GE Silicone II Household Glue, 2.8 oz. Fabric Glue: Beacon Fabri-Tac Permanent Adhesive, 4-Ounce works amazingly well on fabrics, saturating the surfaces enough to provide a very strong bond, but without soaking through. It remains very flexible, e.g., it would probably be great on leather or heavy vinyl (e.g., women's handbags, shoes, luggage, etc.). Previously, I used super-glue frequently on objects (e.g., jewelry) when a clear bond was required---however, Goop is better for such applications, safer, and more conveneient. Opened super-glue keeps poorly, even in tighly sealed glass containers---so I recommended packages of multiple very small tubes. Most construction adhesives are slightly flexible, and so can even be used on leather (i.e., to repair a loose shoe sole), etc. As an adhesive, it is the weakest on this list, but is strong enough for many purposes when spread over a large surface, such as the back of a ceramic tile. I could have used construction adhesive (albeit any excess that squeezed out would have been ugly)--but caulking compound was quick, cheap, looks good, and was more than adequate for the job."
"It was likely just a bubble in the granite mix that came to the surface and remained unseen until it got to me. I didn't want to take out the sink and replace it for two reasons: one it is a lot of work and two it seems like such a waste of materials in the environmental sense. I called the company and they would replace the sink free of charge (not install)."
"This is the epoxy Honda calls for when repairing leaks in the block or heads from aluminum porosity. It is very hard and strong and will withstand 550 degrees F. The key is to clean the surface completely."
"Make sure whatever you are fixing has a clean surface free of paint and dirt and you will have a strong repair."
"I sanded the end of the support rod and sanded the broken weld spot on the main pole, then applied the J-B Weld."
"This is the strongest commonly available epoxy I use and I have used a considerable number of packets over the years."
"I tried a few other brands glues for my shoes and they didn't stick long."
"Only compliant is that it is a little 'runny' before it dries."
Best Tile Epoxy Adhesives
Kit Contains: 1-Gram LCA Gel Syringe | 2 dispensing tips | 1 2" curing sheet | 3 sheets of gel-coated sandpaper | small LED curing light | polish paste packet | microfiber polish cloth (enough material for 5 to 10 small repairs) | If you need to polish your repair to a high gloss, we recommend our Polish Block (light scratches) or our ProCaliber Polish Kit for heavier scratches or for the highest possible gloss finish - For proper and complete curing, apply gel in 2.5mm (1/8") layers and cure with blue light before applying more gel.
Reviews
Find Best Price at Amazon"Used it on a granite sink with a crack."
"One thing that's short of five star is the light included can only cover a small area for the gel to harden so it takes me multiple 5 minutes spot light time on different points to harden a 3/4" long strip."
"This product dries clear and after sanding and polishing it, it is indeed translucent. It is well worth the money and little effort to try this product on small chips."
"3 things that helped me with repairs: I started with smaller nicks to practice; I used a single razor blade to shave the filled area flat to the surface instead of sanding; and I suspended the curing light between 2 teacups to allow more time for curing than recommended. I was really concerned about the big repair because it was a bit more than half an inch wide & about as deep, AND on the counter edge, AND in a highly visible place. I spent a couple hours on all repairs (had to redo the first one two times because the gel was removed with the plastic when cured for only 5 min) but I couldn't be happier with the results."
"For years I've relied on the great reviews on Amazon to help make informed purchases, and yet I've never contributed to the feedback loop myself."
"I had a hard time keeping the light provided to stay on, so I used my gooseneck Ott light over the numerous chips for a longer drying time."
"I had a huge chip along the curved edge portion of my granite kitchen countertop, and wasn't sure if this would be able to fix the chip well."
"Works great, i really have to look for the chipped edge to actually find out where was the problem, would post a picture but you really cant see it."
Best Aerosol Adhesives
The product is 17.6 oz Spray Adhesive.
Reviews
Find Best Price at Amazon"I used this to carpet my subwoofer box."
"Easy to control the spray to go where it is needed."
"I used this to stick then sheet of rubber to the bottom of my home made wooden jig."
"I had to glue the insulation to the inside of the hood of an old classic car, and it worked perfectly."
"A little pricey but, this stuff sticks."
"Worked outstanding while installing new carpet in my C3."
"Very strong adhesive."
"I was trying to add some extra stickiness to my stick tiles in the kitchen."
Best Acrylic Adhesives
Liquid Nails Heavy Duty Construction Adhesive is a multi-purpose, low-solvent, high-strength construction adhesive specially formulated to provide the professional and do-it-yourselfer excellent adhesion and extended working time. Recommended for many exterior and interior heavy duty applications including plywood, particleboard, brick veneers (interior only), foamboard, waferboard, treated lumber, imitation stone (interior only), ceiling tiles, cementboard, drywall, tileboard and 1/8" MDF paneling. Recommended for many exterior and interior heavy duty applications including plywood, particleboard, brick veneers (interior only), foamboard, waferboard, treated lumber, imitation stone (interior only), ceiling tiles, cementboard, drywall, tileboard and 1/8" MDF paneling.
Reviews
Find Best Price at Amazon"This product is fairly versatile in nature--basically a strong adhesive that will work on a variety of surfaces."
"It adhered quickly, but still gave some time to move and adjust the panels."
"It dried quickly but its always good to let this type of stuff sit for a while just to make sure."
"Needed some of this glue does a great job well worth the money."
"omg!"
"helps bond wood to wood and let me use less nails."
Best Silicone Adhesives
Color Name: White. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"After I removed the old stained, cracked and blacked mold caulking, I applied Flex Shot White around the bathtub."
"Works as advertised, very good product."
"It is difficult to get a nice and smooth bead with the tube provided."
"Used this above the RV windshield where metal had rusted through."
"Shower caulking was leaking."
"TV Commercials are not always accurate but this product did stop my leak."
"Opened package and the lid is off, the nozzle is off, and the flex seal has shot out and now the lid is stuck to the box."
"It does not release from the can as advertised."
Best Hot Melt Adhesives
The UBANTE 100Pcs Hot Melts Glue Sticks are created with safe and reliable materials for your arts, crafts, construction needs and more. All temperature: safe for both high and low temperature glue guns.
Reviews
Find Best Price at Amazon"They feed into my glue gun easily and are just the right length."
"It has only been a few days since I use it but so far I do not have any complaints."
"100 mini glue sticks like it says."
"It has only been a few days since I use it but so far I do not have any complaints."
"Decent price without having to go to a store."
"This is a small Glue Sticks perfect for all those little around the house glueing projects."
"It works well for my two glue guns."
"Yay!!"
Best Adhesive Dots
Size: Mini Dot. 600 versatile Mini Glue Dots with clear adhesive sheets for a multitude of projects!
Reviews
Find Best Price at Amazon"It held the iPad on the stand through the entire party of people knocking into it and for an entire week when we had to really pull it off."
"They can be a little difficult to peel off of the backing while attaching to your project, but once you get used to the correct angle, it works great."
"This is an item I wish I had found long ago for kid's crafts."
"I much prefer using these dots on a roll."
"I used a few glue dots and the patch is still on her vest months later."
"I love to use glue dots for card making, especially when adhering small paper pieces or embellishments."
"I was looking for an adhesive that would be clean and easy for the boys to use, but also strong enough to hold the pennies on their collection board."
"- Reliable. - Feels thick and strong. Cons: - A high Price compared to glue dots of lower a adhesive level."
Best Urethane Adhesives
Style: 12 Ounce 8-Pack. When you find a gap or crack that’s a real monster — up to 3" — GREAT STUFF Big Gap Filler is the stuff.
Reviews
Find Best Price at Amazon"I have used my hands to spread lots of things from elmers glue to jb weld. I noticed immediately that I couldn't simply rub my fingers together to "roll" the material to get it off, like you can with most glues. Now I had this satanic cement on my hand AND the paper towel had created a horrid mesh of filth that was resistant to every product known to man. I spent a minute yanking and finally got the towel off and saw the sad reality that all that pulling had made ZERO impact on removing any of the gunk. I started yelling for my wife and begged her to google this filth in order to find a solution....you know....since I couldn't use my phone for lack of having a second hand. I went and sat down on the couch dejectedly and turned on Season 5 Episode 4 of Dexter to make me feel better....although it didn't help much. I really needed to go to bed so I hit the shower and tried to wash my body with my brand new plastic hand. Even if the label on the back does say that simple rinsing of water and soap will solve the issue."
"This is a great product, a little bit tricky to use, wear heavy gloves when uses and think twice before your apply because there is no easy way to remove it also when it came in contact with other materials like concrete, wood or paint it can show up on a dark ugly color, as i said before wear gloves and protect the area you don't want to mess up."
"Filled very large holes in the exterior wood of a house ( temporary fix, Guests were on the way and no time to do proper wood work )."
"This stuff works great buy I can't emphasize this enough."
"Before I bought this, my life had huge gaping holes, especially under the patio door sill."
"Gap filler dries SOLID and white."
"The name says it all, it is "Great Stuff" I had a leak between the deck cover at the back of my house in front of the entrance door that nothing seemed to even partially fix."
"In the photo I tossed the snozzle in the bin I was filling for a reference on size versus the snozzle."
Best Conductive Adhesives
FastCaps revolutionary two-part, ten-second adhesive forms a fast, permanent bond on almost any surface from plastic to wood--without clamping. Simply apply adhesive to one surface, spray activator on the other, hold for ten seconds, and you'll have a joint that lasts forever. Now packaged in a convenient, larger eight-ounce size, the medium 2P-10 formulation works beautifully on smooth surfaces such as melamine or laminate. 2oz sample kit of all of our adhesives plus activator and debonder.
Reviews
Find Best Price at Amazon"This product i was put on to by another tradesman."
"Ought this glue kit primarily for woodworking projects, used the Jel glue to glue together some scrap trim that was being used on a hobby project."
"I don't have as much need for some of the components, but it is a solid starter kit for anyone getting into the system."
"The bottles do clog over time and there isn't enough activator for the amount of glue supplied in kit."
"But the convenience of having multiple viscosity types plus the activator in the same kit...a big plus."
"My personal usage: Gel: easiest to apply but if you are not careful, the activator may set the glue before you have pressed the parts fully together."
"when i went to use the gel I found it was really hard to squeeze and get the glue out, upon further inspection it appeared to have been clogged."
"Bought this product to fill some cracked granite I had in a rental."
Best Adhesive Tapes
ESSENTIAL TO ANY TOOLBOX – So many uses; secure your computer, TV or any other cables down to the floor and out of harms way; tape doors and windows to prevent drafts. PEACE OF MIND SHOPPING - We sell real professional gaffer tape and if you're not satisfied, we back it up with a replacement roll or full refund.
Reviews
Find Best Price at Amazon"I used the white gaffer tape to tape the cable so that it would blend in with the walls and ceiling as much as possible."
"I was in a hurry and ordered this brand rather than the other USA made brand I typically get, since The Gaffer Power tape seemed like a deal and had great reviews."
"I am not in the entertainment industry but use your tape in my workshop for a variety of jobs and and have even found it excellent for attaching sandblast stencils onto custom items which I make. If the tape will withstand 100 psi of pressurized air loaded with silicon carbide grit, it is really tough stuff."
"One of our helpers just pulled the cable up and the tape curled around and stuck to itself. First purchase worked so well that we decided to keep an additional supply on hand for our next production."
"We have dozens of different types of tape in several locations around our home. If you are used to 3 rolls for $1 department store tape, Gaffer tape might surprise you."
"Having fought duct tape for years (I maintain one of the strongest bonds in the universe is duct tape stuck to itself) I had no issues using this to secure my cables at an event over the weekend."
"http://www.amazon.com/Professional-Premium-Grade-Gaffer-Power%C2%AE/dp/B00GZE3UJ8?ie=UTF8&ref_=cm_cr_ryp_prd_ttl_sol_0. This is my first experience with Gaffer tape, so all I can compare it to is duct tape."
Best Resorcinol Adhesives
Use Aerodux 185 liquid phenol-resorcinol resin adhesive mixed with a powder hardener provides cold-setting weatherproof and gap-filling adhesives especially suited to the manufacture of exterior high hazard structural components as defined in BS 5268 : Part 2. Aerodux 185 with hardeners HRP.150 and HRP.155 has been tested according to the German Standard DIN 68 141 by the Otto-Graf-Institut (MPA) in Germany and found to suited for gluing load-bearing wooden structures for indoor and exterior use in accordance with DIN 1052. Aerodux 185 with Hardener HRP.150 and HRP.155 is also approved by Luftfahrt-Bundesamt for the production of of glued wood products to be used in aeroplanes. Compare to: Hexion RS-240, Hexion G-1131, DAP Resorcinol, CP-0900 Resorcinol.
Reviews
Find Best Price at Amazon"I did lots of research to the type of glue to use and this product came highly recommended."
"As noted."
"if it weren't for the price this would have gotten 5 star!"
"I bought 5 gallons and have used one gallons so far on laminating a keel."
"This is the probably the strongest glue that you can find for gluing wood together."
"Wish we had know about this type of glue before we started using epoxies two boat projects ago."
"Water soluble when wet (easy cleanup)."
Best Urea Resin Adhesives
Bondo All-Purpose Fiberglass Resin is 100% waterproof and designed specifically to be used with Bondo Fiberglass Resin for interior and exterior repairs. Compatible with all paints and gel coats and includes Bondo Fiberglass Resin Liquid Hardener.
Reviews
Find Best Price at Amazon"Product came as described, was delivered on time and the price was reasonable."
"used to seal cracks in concrete."
"dose what it is made for it was fresh."
"fresh product, as advertised."
"did NOT Know the resin would be brown when i tried to make a large copper and crystal orgonite pyramid lol."
Best UV-curable Adhesives
Formulated to produce remarkably strong, permanent bonds for all climates, and can pass a two-year weather, age and field test.
Reviews
Find Best Price at Amazon"Used this on a pretty big chip in mid 20 degree temp."
"Just what I needed love it, fast shipping."
Best Cyanoacrylate Adhesives
We combine innovation and technology leadership and close customer partnership to deliver solutions that are an essential part of countless industrial and consumer goods. Loctite Super Glue Professional has proven superior performance over ordinary super glues. Super strength formula for repairing figurines, costume jewelry, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings. Bonds leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglas, polycarbonate, polystyrene and PVC.
Reviews
Find Best Price at Amazon"I left this glue on my table overnight, loosely capped, and found the glue glued to my table... permanently. My colleagues and I have tried many means to get rid of the glue, mainly just prying at it (ouch, our fingers), poking at it with chopsticks (our chopsticks are dulled), cutting at it with knifes (I think the knife is bent), lathering on nail polish remover (my table is flooding), sawing at it with string (the string broke in half), and getting the glue stuck on our fingers, which took quite some to get off."
"* NOTE: If You Get Any On Your Skin, It Can Be Easily Removed By Buffing Lightly With An Emory Board. * It Bonds Glass, Fabric, Metal, Wood, Ceramic, Skin, Rubber, Plastic.... Everything I Have Attempted To Repair. * Today I Used This Bottle To Reattach My Broken Charcoal Grill Knob, Repair My Reading Glass, Attached The Heel On A Shoe, Put The Name Tag On My Flight Bag And To Apply Fingernails (One Drop For Nails). * With the help of my husband, We Cleaned With Peroxide, Then Applied Loctitie Professional To The Inside Wound Edges. * The Non-Drip, Precision Tip, And Gooey Texture, Make It "Super" Easy to apply in Exactly The Right Place. * Often, I do add a tiny drop of water to a surface to speed drying time. * If you have any questions feel free to click my user name, it is a hot link, and I will answer you."
"My favorite super-glue."
"My husband and I both do a lot of crafting."
"You can glue your eyes shut with this stuff!"
"This glue is amazing."
"Delivered on time and is a great super glue and nozzle does not plug."
Best Adhesive Primers
The activator is designed to promote the speed of cure of Loctite anaerobic adhesives and sealants such as Loctite 680.7649 can be used with Loctite 680 (PN:680) on specially designed Anaerobic connectors to increase the cure speed.
Reviews
Find Best Price at Amazon"Loctite doesn't need this for metal on metal, but in the metal on carbon situation I was using it in this is great added insurance to make the loctite do its thing."
"Used this product while putting my Harley back together."
"great product."
"Really made a difference in holding strength."
"I use this as activator for Loctite 680 to hold a strand of fiber optic cable in a hand polished connector."
"This is the required primer for Loctite 680 use it or lose it."
Best Methacrylate Adhesives
The ChemSet TrimGrip Adhesive from Chemical Concepts contains everything a contractor needs to permanently bond, laminate, and fill gaps or nail holes in Cellular PVC or natural boards and trim. Formulated for outdoor use, TrimGrip adhesive can be used for joining or laminating sections of trim, columns, or cornerboards; bonding aluminum cleats to PVC window and door trim moldings; and filling gaps and nail holes for a smooth look.
Reviews
Find Best Price at Amazon"Was not happy with product found a product called Crack Shot that was easier to work with and better result and much cheaper sorry but I could not reccomend your product quite disapointed."
Best Thermoplastic Adhesives
♥✉ If you have any question about the products, please feel free to contact us before leaving the feedback, we will deal with the issue immediately and carefully until you are satisfied.
Find Best Price at AmazonBest Water-based Adhesives
This clear wood finish brushing spray 100-Percent nitrocellulose brushing lacquer for most interior wood and metal surfaces. Use clear wood finish to seal and finish interior wood furniture, cabinets, paneling, antiques, and crafts. This clear wood finish brushing spray 100-percent nitrocellulose brushing lacquer for most interior wood and metal surfaces.
Reviews
Find Best Price at Amazon"On an overcast day, the product still dried in 2-3 minutes, and I was able to build up 5 coats in about an hour, sanding with 400grit before the final coat, and the project came out smooth as silk."
"High quality product, arrived quickly, worked perfect as usual."
"However, the poly I've used also tends to yellow the maps."
"I've used this on a couple of wood carvings and was pleased with results."
"I need this product (or something similar) for wood name badges I make."
"This product is outstanding, easy to use and produces a great Finnish."
"Excellent finish."
Best Solvent-based Adhesives
SCIGRIP offers unique adhesive solutions for bonding a range of substrates including metals, thermoplastics, and thermoset composites . It will also bond rigid PVC, ABS, styrene, butyrate, polycarbonate to themselves and each other, as well as other plastics and porous surfaces.
Reviews
Find Best Price at Amazon"Normally you would squeeze a tube like this. Also, positioning the item so that the liquid cement won't run into a corner or off of the project will help."
"I was making an overflow and wanted to weld it to the back of my aquarium and the first pass with the weld on #4 worked very well but I wanted piece of mind and simply did another layer with weld on #16."
"I used this to repair an aquarium overflow box that had cracked."
"The glue is great, the tube container is a bit frustrating."
"Do not use I’ll much and only use a wood stitch to spread it out."
"The glue in this thing wants out."
"The glue works fine!"
"This glue is great for bonding almost any plastic or acrylic."
Best Thread Locking Adhesives
Eliminating the need for stocking expensive lock nuts and lock washers, this threadlocker locks and seals while preventing parts loosening due to vibration. Suggested Applications: valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts, carburetor studs.
Reviews
Find Best Price at Amazon"Remembering that I had bought some small gauge blunt tip needles (bought on Amazon) for use in filing some small plastic bottles for another purpose, I thought that one of the needles might fit on the nozzle in the tip of the Permatex threadlocker bottle."
"I purchased this product for some brake jobs I am doing."
"This stuff just works."
"Also if this product seems to not work you are probably putting to much on the nut etc., and are probably not allowing adequate drying time."
"Great to have in the house."
"I fixed my macbook pro's monitor bouncing problem."
"Used on a gear shift screw that slowly wiggled loose and threw the shift lever off to the point that it sometimes did not want to go into park."
"Really great at holding screw heads wherever there is vibration of any kind."
Best Adhesive Dispensers
The 958-G01 is a 7-Piece set of Streamline Spatulas.
Reviews
Find Best Price at Amazon"It is exactly what it says and it's perfect."
"good quality product but when new can leave scratch if you press the spatula to hard against the superfice."
"great set of tooling knives, beware the split ring though, mine crapped out after only two times opening and closing it."
"These work great for smoothing caulking joints of all different sizes."
"Great set of spatulas a little stiff but with the rite grip leaves the perfect caulk bead every time."
"great deal on great tool."
"Love these tools easy to use makes a great tooled seal and easy to clean."
"Great item original fast shipping."
Best Polyvinyl Acetate Adhesives
waterproof glue, adhesive cleans up with water and does not affect finishes.
Reviews
Find Best Price at Amazon"I haven't opened this up yet, but the smaller sizes of this product that I have used in the past works great."
Best Adhesive Accelerators
Vibra-TITE Excel 624 General Purpose Accelerator is an ozone friendly accelerator used for normal curing of cyanoacrylates and to prepare the surface for bonding. Excel 624 is also designed to provide a fast cure of thick deposits of SuperGlues or for post curing excess adhesive outside of the bond line. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"For those first time buyers be warned that this impact resistant accelerator produces white film instead of clear, if you want the clear one get the other version."
"Works great for the cyanoacrylate products like superglue."
"Works great with all brands of superglue."
"Please take note of the manufacturer's comment at their website [...]: "Excel 624 is an isopropanol based accelerator that WILL WHITEN the adhesive's exterior bondline for easy inspection, and will not crack polycarbonate.""
"Product and picture description is a bit different."
"Teflon tape won't seal straight threads, especially ones as poorly formed as these."
Best Ethylene Vinyl Acetate Adhesives
Century 3D PLA Printer Filament 1.75mm 1kg spool 2.2 pounds Dimensional Accuracy +/- 0.05 mm (Brown)
Century 3D is a professional 3D printer filament manufacturer specialized in providing various colors and materials for 3d printing. Because of the lower melting temperatures and lack of warping, PLA filaments retain their color vibrancy and are a common choice for displays or small household prints. Century 3D always produces the best PLA filament to maintain smooth and consistent printing experience that achieves best printing result. Spool Diameter: 7.9" - Spool Width: 2.7" - Spool Hub Hole Diameter: 2.2".
Reviews
Find Best Price at Amazon"This is a review and response to the person that said that the filament kept slipping."
"Quality product, shipped quickly."
"This stuff is working well for me."
"I havent gone through the whole spool yet, but i had no issues using this with my anet a8 with."
"Prints great!"
"Awesome filament, Spool is solidly constructed, and its well with a desiccant pack."
"I ordered the brown color filament to make some toys for my little son."
"As for the filament spool itself, this filament came in a vacuum sealed packaging with a silica pack. It continued to slip and clogged a 3rd time. In the interest of time to avoid installing a new grub gear , I loaded the filament on another 3D printer that just recently I had replaced the gear on. Again, on the second printer the issue recurred and this time, the filament clogged and had bound to the inner PTFE lining of this printer. After cleaning both Printer clogs, I really wanted this filament to work given the price, but unfortunately given the issues I experienced I cannot recommend this PLA filament to other 3D makers."
Best Anti-Seizes
Milesyn SB 5W30 API GF-5/SN, Synthetic Blend Motor Oils are specially formulated using synthetic and Group II base oils and high performance additive packages to provide superior performance in gasoline fueled and flex-fueled engines. These oils are formulated for excellent oxidation stability and low temperature properties to insure protection during cold starts.
Reviews
Find Best Price at Amazon"VERY GOOD QUALITY FOR THE PRICE."
"Wow great oil great price, I will never go back to buying single quarts or gallons this is great!"
"Great oil , great pricing."
"The label displayed does not show the API certification symbol so I checked the API site and the Milesyn brand name is approved to ratings SN and GL-5 with license valid through March 2018."
"It works great, I change my oil every 7,000 mile and the engine is running smooth."
"Made certain the SAE stuff matched the requirements in the owner's manual."
"All in all, you can't beat $2/qt for good oil, and when it's gone you've got a free bucket with pour spout lid (about a $8 value)!"
Best Catalysts
16 oz squeeze bottle with measurements.
Reviews
Find Best Price at Amazon"perfect for what i need these for-."
"Perfect for MEKP, only has 5, 10, 15, 20 CC on it otherwise easy to use."
"Very nice and convenient."
Best Contact Cements
Reviews
Find Best Price at Amazon"Barge All Purpose Cement, 2 oz, Neutral. This stuff works amazing on leather."
"Bought this product to try and adhere the felt pads back down on a pair of waders."
"I bought this because I had a button fall off a leather chair of mine and after a few failed attempts to use super-glue, I decided to go for a more research based approach."
"Works well, butter gloves because it gets all over your hands and is very difficult to get off."
"Not sure why everyone is complaining about the formula change."
"The cement worked well for adding half soles to my boots."
"I've been using Barges for decades in my woodwind restoration business."
"When bought this product, the image was of a yellow tube of barge glue."
Best Light Cure Pens
Ensure that you hear the clicking of the mixing bearing hitting both ends of the barrel, and continue shaking for a minute after that. If heat curing, do not exceed 65 °C as this may cause surface defects due to solvents evaporating off too quickly.
Reviews
Find Best Price at Amazon"You have to shake really well, hold the "pen" at just the right angle, push down with just the right pressure, and squeeze the exact right amount to get anywhere near a smooth flow."
"This stuff worked great repairing worn contacts on a 50 y/o record player."
"I used it to repair connectivity breaks in an adhesive aluminum sheet inside dance pads."
"I am not that good at soldering and most definitely not small joints."
"I tried to use this to save an electronic car key but it didn't work."
"Worked great for me."
"worked great for repairing those rubber "remote control" buttons."
"Fixed the control panel in my dishwasher with this."
Best Industrial Sealants
Ideal for use in sunny environments. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Knowing that the roof on the RV would eventually leak because man was created foolish enough to forget to put a cover on his RV in the hot sun, God created EternaBond Roof Seal tape. Do you want to seal the fine cracks in the EDPM roof rubber on your RV - FOREVER? You cut it to length, peel the clear backing off and firmly press it onto the roof of your coach. It will probably outlast the roof around it until you are left with no rubber roof save for the parts you stuck this onto. My plan is to slowly cover every inch of the roof on my 34' Bounder over the next few years until it is completely covered. Seriously - if these guys made a peel-and-stick roof covering in one piece I'd use it, except for the fact that I fear I would be in real danger of becoming stuck to it during installation, leaving myself helpless on the roof of my RV like a wayward mosquito caught in the web of a black widow, or a criminal caught in that spider-individual's web of justice, resigned to my fate of imobility. Fifty feet of this stuff is a lot, but at the same time you might be surprised how many little cracks and stuff you have up there, plus it is good to have some on hand in case of future leaks, or the sudden need reattach an arm after a bazaar kayaking accident."
"I bought it to anchor the new flexible, thin solar panels I purchased to the roof of my travel trailer."
"The guy in the Eternabond video uses his fingers to apply pressure (not the roller) and he uses a utility knife to cut the tape. Something else about the utility knife is important which is that it can be used to easily lance any air bubbles or "tents" that occur has you apply the Eternabond. The Eternabond website says to use a pin to pop air bubbles and describes the procedure for what to do for "tenting" and I found that also very helpful. As it shows that where it tents or bubbles, the important thing is only to lance it and smooth it over and apply another layer if necessary or to make it prettier. I am totally new to this and could be doing it wrong so I'm just going to get to the pictures ... First I noticed the trouble spot by the back rear where the caulking was breaking down and this looked like an area where it was possible for water to pool. When I applied the eternabond tape, I pretty much put it above where I wanted it (with back peeled off) and let it kind of fall into place by gravity as I guided it laying it as flat as possible. then when it was flat, I went about applying pressure from the middle out and working out all the tents and air bubbles and I pressed on the sealant. I used: pair of nice, sharp scissors to cut the tape (clean scissors as necessary with acetone if they get gunked). utility knife (clean with acetone if it gets gunked). acetone as described above. dishsoap as described above. my fingers to press down to ensure surface adherence (not the roller). On purpose here I did not use the tape over the black rubber or the gutter because both are in good condition with no breaches so I wanted to leave them as-is."
"I used "100 mph tape" many times in the Navy including once fixing a 25' aluminum boat that hit a bouy ( I think that guy was from the Coast Guard) but this stuff is 10x better."