Koncocoo

Best Acoustic & Classical Guitar Parts

K&K Pure Mini Acoustic Guitar Pickup
The Pure Systems are definitely different. Feedback Resistance How safe is the Pure System with feedback? Technically, a pickup installed in or on the bridge is a lot less likely to feedback than one which is attached to the open sound board. Three Transducer Pickup System for Steel String Guitars.
Reviews
"Elderly's wanted $100 to install it, and I did it in about 45 minutes, including gathering the tools and a couple dry runs, saved $100 - easy - cheesy - lemon squeezy!"
"this product is excellent.it gives you back what your guitar sounds like.there is no quack .I plugged directly. into Roland cube 30 amp using the acoustic setting with some reverb,i could not tell it was on until i turned off the amp.I did not use a preamp ,I don't think you need one,even though it is a passive pick up the signal is strong.this is the second unit that I have installed, one on a Lowden O-23 and the other on a Mark Angus 12 fret,these are both high end guitars.I did glue the transducers(three) to the. bridge plate as per instructions it was not difficult,the Lowden was bit more tricky because its a split saddle and you have no end. pin holes as a guide.I practiced a number of times when I felt comfortable before I went ahead and used the glue which gives a stronger contact than the double sided tape.If you do not feel secure doing this,especially if you have high end instruments have it done by a. professional.I used this for more volume in a small venue solo guitar sound was excellent."
"Amazing acoustic sound reproduction from such a simple, hassle-free product!"
"Tip, get a long narrow mirror and put it inside the guitar to do your evaluation and to check progress of placement of pickups during installation."
"The product is very good for the price."
"I needed a good, but simple pickup for my old acoustic Gurian guitar."
"If you have a vintage guitar I recommend the vintage package, as you don't have to drill out the end hole."
"I went after this style of pickup to capitalize on the warmth of my guitar and it did just that."
Find Best Price at Amazon
HDE Guitar Pickup Acoustic / Electric Transducer
Get your classical rock on with a clip-on pickup that will turn your acoustic guitar into an electric wonder with minimal cost or set-up. Captures mechanical vibrations and converts them to an electrical signal which can then be amplified, recorded, or broadcast.
Reviews
"Put it on an old Fender BG-20 bass with dead Fishman active electronics."
"This has been easy to use and has been VERY helpful to me when I have had to play in a crowded place with a lot of talking."
"The reviews alone sounded promising the only person with negative feedback said it was probably because of his own equipment."
"I ordered this for my Epiphone acoustic so I could play it through my Laney GC80A which has a separate side just for acoustic."
"At first I was going to buy a Seymour Duncan or a Dean Markley, but when I saw this I decided to give it a shot."
"I was hoping to get a clean sound from my acoustic."
"Bang for the buck, I am thrilled, I seriously didn't think I could get such great sound quality from such inexpensive pick ups!"
"I haven't tried it with my rock Smith yet because I need to purchase a coupler, but I see no reason why it wouldn't work. Originally, I went to a guitar store to price pickups, and they suggested a 70 dollar piece."
Find Best Price at Amazon
Hosa CMS-103 3.5 mm TRS to 1/4 inch TRS Stereo Interconnect Cable, 3 feet
5mm Male TRS to 1/4in Male TRS Stereo Interconnect Patch Cable 3 ft. Quality connectors for your stage or studio.
Reviews
"I run it from the stereo headphone/aux output of my yamaha pss-380 keyboard synthesizer into a dbx go-rack processor which feeds into a crown xls1002 class D power amp and two pair of andrew jones design pioneer speakers.....yeah.....it sounds awesome!"
"I use it with a Morse code paddle."
"This cord works great!"
"Used this to jury rig a microphone feed into an old cell phone used as a web cam."
"Superb adapter, especially for guitar players who deal with 1/4 out from pedals to 3.5mm auxes or vice versa."
"The cable works fine, however it's a bit thin/flimsy, the connectors feel low quality and the strain relief could be a bit better."
"I put the 3.5mm end into my Monoprice headphones, and the 1/4" end into one of my Focusrite Scarlett 18i20 headphone outputs."
"Before purchase, I didn't notice other poor reviews warning of defects & poor return policy."
Find Best Price at Amazon

Best Guitar Bindings & Trim

Kmise Z4859H5 New 5 Pieces Parts ABS Guitar Bindings White 1650mm x 5mm x 1.5mm
100% new high quality and testing is fine Item 100% like the picture shown Guitar bindings for Guitar maker or luthier Thick guitar binding is great to use Material: ABS Size: 1650 x 5 x 1.5 mm. Guitar bindings for guitar maker or luthier, fits for acoustic classical guitar body project.
Reviews
"The binding has a very clean and professional look, however a heat gun is a must when forming this binding."
Find Best Price at Amazon

Best Guitar Bridges & Bridge Parts

SUNYIN Acoustic Guitar Tool,Kit for Starter with Guitar Strings Winder Cutter Tuner Bridge Pins Picks & Pick Holder,Everything Set for Change the String-ordinary
• Music(Acoustic Guitar) Makes you get more skills, more confidence, more charm, as a starter , are you still worry about replacing strings? 4 x Pick(color and size is random). 7 x Guitar string. ❤ EVERYTHING YOU NEED-Guitar Tool kit including 7 string(Extra e string),Durable tuner, Small Cutter,Convenient String Winder,Bridge Pins,Picks and Pick Hoder.
Reviews
"The string changing kit is a great value for anyone with a guitar so they don't have to pay someone else for routine string changes."
"My son was very happy with this set."
"This kit was perfect for a student learning the guitar."
"Honestly, the pick and pick holder is the best thing out of this entire box. I love the picks and the holder (as I tend to lose picks quite often)."
"Great kit."
"Junk."
"Great kit to have, awesome gift for a new guitar player."
"very useful tools for a guitar."
Find Best Price at Amazon

Best Acoustic & Classical Guitar Frets

Guitar Fret Wire - Standard Medium/Medium Size, Nickel Silver - Six Feet
This fret wire is identical to Stewart-MacDonald's #148 "Medium/Medium" fret wire, and can be used to repair/replace frets on an existing electric or acoustic guitar, dulcimer, larger banjo, cigar box guitar other standard sized stringed instrument. Six feet of beautiful, durable 18% nickel-silver fret wire - the most popular size for acoustic guitars.
Reviews
"Great frets, would rather they came in one length vs 8 inch strips."
"Exactly what I wanted, delivery arrived on time."
"enough for two cigar box guitar will buy from cb gitty again."
"It's good fret wire."
"It's fret wire, standard and of good quality."
"Great wire, you don't have to straighten it like other suppliers, and a very good price."
"Worked great."
"I'll definitely hit up their provided website in the future as the frets I got were excellent."
Find Best Price at Amazon

Best Acoustic & Classical Guitar Necks

Fender Stratocaster Neck - 21 Fret - Maple Fingerboard
Genuine Fender Stratocaster guitar maple neck features a comfortable "modern C" profile and 9.5"-radius rosewood or maple fingerboard with 21 medium jumbo frets. Maple w/Maple Fingerboard.
Reviews
"The fine folks at Fender must have read my RMA because the replacement neck had multiple inspection stamps where it bolts to the guitar body. My brother then took the guitar to a local music store and requested a Plek (Google it) treatment be done on it. When my brother returned to the store the luthier informed him the Plek report showed the neck was perfect, all it needed was to have the nut properly filed. Then Fender provided us with a PERFECT replacement neck at a very reasonable price and now his ten year old Strat plays better then ever."
"Just the item I needed to build my own personal custom made genuine "Fender" guitar."
"That will fit, mine did got info from fender.com Good body a bit dark but i like it sounds good made of 3 pieces but most fender guitars are even the expensive ones.has a hole for some reason you can see it on amazon picture But wiil be coverd with pickguard."
"The unfinished parts are level and fairly smooth so no issues there with mounting the trem or the neck."
"Real fender body."
"Very beautiful neck."
"Quality product!"
Find Best Price at Amazon

Best Acoustic & Classical Guitar Nuts

GraphTech PT606000 TUSQ XL Black Self-Lubricating Slotted Nut, Epiphone Style
Compared to standard materials, you'll hear crystal clear bell-like high end, big open lows, and a noticeable increase in overall sustain. TUSQ XL is engineered from the same material as TUSQ and is impregnated with PTFE which is five times more slippery than graphite.
Reviews
"Definitely an upgrade from the cheap plastic nut on my old guitar, which chipped and would no longer hold a string properly."
"In my opinion, Tusq XL nuts are the best Bang For The Buck upgrade, for any guitar, Imported, or US built."
"Ran into some issues with the Les Paul Jr, The neck on the Les Paul Jr is slightly smaller the the Special II so it needs to be fitted by shaving it down."
"The first one I used on a DIY guitar, I had to shave it down a bit but it worked perfectly."
"I replace most of my guitar nuts with TUSQ."
"These guys make a great product, but be sure to measure and size them properly to avoid any issues."
"It was a perfect fit on my Epiphone Les Paul Standard."
"This was my first ever attempt to replace a nut and it was an easy job on my Epiphone LP Special P90."
Find Best Price at Amazon

Best Acoustic & Classical Guitar Pick Guards

Fender Modern Pickguard, Stratocaster, 11-Hole - White Moto
Size: Stratocaster - 11 Hole (Modern) |. Color: White Moto. Double check your screw-hole pattern to ensure you chose the right model.
Reviews
"The original pickguard was only shielded around the knobs - the new pickguard is totally shielded."
"Such a great purchase!"
"A beautiful guitar, but a white pickguard is bland and I really wanted the tortoise shell pickguard look. Installation was about as easy as you would expect for a guy who's never done any DIY customization like this on his guitar."
"On both occasions I received my order 2 days ahead of schedule and in perfect condition and they are branded Original Fender Parts , you are getting the real deal , but paying far less. http://www.strat-talk.com/forum/stratocaster-discussion-forum/338650-look-what-i-have-done-my-strat.html. I strongly suggest that you buy your gear from Amazon , I have had nothing but kindness and personal consideration from them , on rare occasions when I needed help."
"I had to drill a small hole in it to accommodate an extra pickup-selector button that came on my deluxe players strat, and this pickguard did not crack or scratch at all even with my shotty craftsmanship."
"Put this on a Mexican Strat I was modding with Custom 69's."
"However, I put it on a 2010 Squier Affinity Series Stratocaster and all holes line up except for the one at the bottom right next to the tone knob (see pics)."
"new pick guard form my Sunburst Fender Squirer, easy to install, holes lined up nicely."
Find Best Price at Amazon

Best Guitar Pickups & Pickup Covers

K&K Pure Mini Acoustic Guitar Pickup
The Pure Systems are definitely different. Feedback Resistance How safe is the Pure System with feedback? Technically, a pickup installed in or on the bridge is a lot less likely to feedback than one which is attached to the open sound board. Three Transducer Pickup System for Steel String Guitars.
Reviews
"Elderly's wanted $100 to install it, and I did it in about 45 minutes, including gathering the tools and a couple dry runs, saved $100 - easy - cheesy - lemon squeezy!"
"I saw the reviews, and installed the K&K Pure Mini's: First in my Martin 000-28VS, and then in my Recording King copy of the Martin parlor. Think warm, rich tone that is great for strumming, melody, percussive styles, and all. I purchased a guitar 'mirror', and the proper tools for enlarging the guitar end-pin to 1/2"."
"I wanted a guitar pickup that would faithfully reproduce the natural sound of my steel string acoustic guitar."
"I read many of the reviews here, went to the K&K site and asked friends. Finally, I contacted the luthier shop I planned to have install it. Gone is the high end nastiness found with the bridge piezo pickups."
"BUT then I got a Fishman Aura pedal on Craigslist, and now I am very happy with the sound. I am sure that an expensive professional installation may have improved the sound quality without the Aura pedal, but the improvement with the pedal is dramatic."
"The K&K mini does a good job of re-creating an acoustic tone for a modest price. Two other good things; It doesn't seem to affect the acoustic sound of my guitar, and if you choose to remove it, a single edge razor blade (and some very careful work) get it out with no permanent change to your instrument."
"Minimal wiring and electronics inside and the sound is great."
Find Best Price at Amazon

Best Acoustic & Classical Guitar Saddles

GraphTech PQ-9280-C0 TUSQ Fully Compensated Acoustic Guitar Saddle
Color: Ivory. 1/8-Inch thick.
Reviews
"IMMEDIATE sound increase using this bridge over the previous plastic cheapie."
"It's great, it's very dense and resonant which helped with the tone of the guitar."
"Very hard material."
"I bought a new 2016 Gibson Custom J-45 a few months ago and I found that the B string and high E string were muted and wouldn't stay in tune."
"My guitar came with a plastic saddle in it. Because I've it setup with the string height of a lap guitar / Dobro, I didn't have to do any work on sanding down the saddle. Before trying this saddle, I made two other upgrades to the guitar -- switching from plastic to Tusq bridge pins, and adding a Planet Waves O-Port."
"As many have mentioned, it took quite a bit of sanding and filing to get the saddle to the correct height, width and length to fit my guitar, but the only tool needed is sand paper (and a sanding block) and a file."
"A little patients sanding the saddle to fit my 1973 vintage Guild (better fit than the plastic original that it replaced!)."
"Once installed I did notice less buzz after install but again I had to sand it multiple times, not the products fault just the fault of the way acoustic saddles are adjusted and installed."
Find Best Price at Amazon

Best Acoustic & Classical Guitar Tailpieces

Tonepros LPCM04-C Standard Bridge/Tailpiece Set Chrome New
SPECS: Bridge Post Thread: 10/32 (as used by Gibson on Nashville Models) Bridge Post to Post Spacing: 2.93 Inches/ 74.mm Saddle Notch: Pre-Notched Saddles Saddle Material: Zamak Bridge Material: Zamak Bridge Post/Thumbwheel Material: Brass Radius: 12 inch Bridge String Spread: Approx. 10.4mm Tailpiece Stud Thread: 5/16 - 24 US Thread Tailpiece Stud to Stud Spacing: 3.22 inches/ 82mm Tailpiece Material: Zamak Stud Material: Brass Finish: Chrome. Bridge post to post spacing: 2.93 inches/ 74 mm.
Reviews
"Worked better and is better built than the bridge/tailpiece that came on my Gibson SG!"
Find Best Price at Amazon

Best Acoustic & Classical Guitar Tuning Keys

YMC Chrome-Tuning-Peg-Round220-3L3R 6 Pieces 3L3R Semiclosed Guitar Tuning Pegs Tuners Machine Heads
100% Brand new, never used. Item 100% like the picture shown. Set of 6 quality chrome machine heads for steel string (electric or acoustic) guitars (3L + 3R). Quality Semiclosed machine heads. Heavy duty internal gear. Material:zinc alloy and plated chrome. Colour:chrome. Package Includes: 1 x 3R3L Guitar Machine heads (Semiclosed). We manufacture all kinds of instrument parts and product The direct model so that our price is very low with high quality. YMC Chrome Tuning Peg 6 Pieces 3L3R Semiclosed Guitar Tuning Pegs Tuners Machine Heads.
Reviews
"I did have to pull off the back covers (easy to do) and tighten up some of the screws that hold the gear on but other than that they function well and fit exactly on the vintage tuner holes in the peg head."
"I recently purchased an acoustic guitar from Goodwill and noticed it was missing one of the tuning keys and another tuning key was missing the washer it fits in."
"Chrome Shroud on the machine head covers that work."
"Great low price."
"Great value priced tuners."
"Replaced a set of tuning pegs on my 30 year old Yamaha acoustic."
"I bought these to fix up my first guitar (Uno by Hutchins) I got when I was 12 (I am now 23) I ended up striping them down for the screws and the tuner part because, the part you screw/drill into the guitar DID NOT fir my guitar. Anyways here is a quick summary. Good: 1."
"You get what you pay for."
Find Best Price at Amazon

Best Guitar Wood & Inlay Material

Fretboard Markers Inlay Sticker Decals for Guitar - Gypsy Rose
These sticker could cover original dot marks easily.They will not get caught by your fingers while playing! It possible to use such as finger ease spray or lemon oil. You can install these on your electric or acoustic guitar with 24 3/4 inch(628mm) 25 1/2 inch(648mm) guitar.
Reviews
"Easy to install."
"Put these on my martin and everyone thinks it's real inlay."
"So I messed up a little as I didn’t know how it stuck on so mines a little different as I used up one of the flowers."
"Good inlay stickers for my tele."
"Beautiful but overpriced."
Find Best Price at Amazon