Best Clothes Washer Replacement Drain Pumps

This is a genuine replacement part. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Note the issue it fixed was a 'grinding' sound in the motor area when draining like there was a diamond earring in there, alas there wasn't but I did find that the motor screws had come loose meaning the impeller was wacking the walls, I had to replace the original with some larger ones from Ace Hardware (thanks Ace Hoboken you rock) - that allowed me to insure a tight fit."
"The drain pump on our LG washer (7.5 years old) malfunctioned a few days after Christmas."
"Great price and looks exactly like the original one that came in my LG front loader."
"The only glitch I encountered was that the original pump housing and new pump once fitted had a gap of a couple mm and to prevent leaking I ended up creating a secondary gasket with some blue, waterproof RTV. If you find yourself in the same predicament, create a secondary gasket with some gasket making RTV, keeping it clear of the pump mechanisms and you should be set."
"Was getting the "OE" error code and a quick search of google led me to this being the issue."
"My washer was purchased second hand, and it hadn't Ben property cared for."
"Part fit perfectly in my LG front loading washing machine, and has been working like a champ."
"Saved me a few thousand on new washer and dryer so well worth it."

Part Number 3363394 (AP2907492) replaces 64076, 3348015, 3296, AH342434, EA342434, PS342434, 3352492, 63347, 62516, 62516, 3348014, 8235, 3363394, 3348215. Works with many Whirlpool, Kenmore, Maytag, and other washing machines.
Reviews
Find Best Price at Amazon"I ordered this Automatic Washer Water Pump because the one in my Inglis Washer had sprung a leak. It was 11 years old and the impeller wheel had finally started to chew through the outside housing making an occasional leak. then I turned the impeller with a big screwdriver and held it in every orientation I could think of to see if it bled out at any seam or the seal for the impeller on the back side."
"Water was leaking from the bottom of my daughter's washer, so I diagnosed this was the problem, ordered it on the cell phone, and two days later, I was at her apartment fixing it."
"You can probably do it in about 30 minutes, but mine took about 1.5 hours because I took the time to clean out all the crud that had built up inside the machine over the years."
"Water was going from bottom upon inspection i found it to be this part. I searched online whirlpool had a breakdown of every part on the machine. After doing this i realized i could have just put the washer on its side and access this part or any part. Remove the two brackets holding water pump to washer."
"The washing machine works fine now, drains properly and no more leaks."
"This was my first time repairing the washer and I was quite nervous before I opened up the machine, so I checked around youtube and watched as many videos as I could find. As all repair jobs specially the ones involving water, it's quite messy but the effort is worth it."
"I bought two and both Damaged."
"Washer was broken and the pump needed to be replaced."

Supco LP280187 Washer Motor. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Amazon (and Google) to the rescue!! The problem is, it could either be a computer control issue or the pump."
"If your drain pump is failing ("02/SUD" codes or loudish grinding noises from pump area) your choices are 1) Replace the entire assembly with new OEM (Askoll) pump or 2) replace the pump only with a cheap Chinese knockoff and hope for the best."
"The whirlpool/Sears HE3t is a poor design; there is a filter/drain point to catch things that get out of pockets and into the water, but there is nothing to stop them getting caught on and damaging the pump vanes (in my case it was the remains of a ballpoint pen which had been inadvertently washed...)."
"Newer washers use a snap-in fitting in the front (the red rubber "bumper" shown in the picture) while the older ones like mine have a screw bushing instead."
"The hardest part was not making a mess; the machine obviously had water since the pump was broken. This pump and housing works perfectly for the Kenmore Elite 3Et front load washer."
"The main thing you need to know is wear the screws are to remove panel and which tools you need - T20 screw driver bit- Flat nose pliers for hose clamp- Towels or shop vacuum. I have had it in for a week no issue will update in a few months."
"In the video I watched prior to the install, it sounded like this new pump should have come with new clamps to connect the hoses, but it didn't, so I had to use the old ones."
"Amazon has pictured the same one as I received and I would have ordered it instead which since I am a Prime member I would have saved $13 on purchase and had guaranteed 2 day delivery."
Best Clothes Washer Replacement Doors

The Frigidaire 131763202 Washer Door Lock Assembly is a genuine OEM replacement part and is compatible with models: GLTF1670AS0, FWT445GES2, FWT449GFS1, GLTF1040AS0. The Frigidaire 131763202 Washer Door Lock Assembly is a genuine OEM replacement part and is compatible with models: GLTF1670AS0, FWT445GES2, FWT449GFS1, GLTF1040AS0. Fits models: GLTF1670AS0, FWT445GES2, FWT449GFS1, GLTF1040AS0.
Reviews
Find Best Price at Amazon"To access the door lock, remove the spring clamp around the front door gasket. Remove the 2 screws on the door lock."
"Washer went from not working to working and the price was right in comparison with the local repair people."
"(On my machine its located within black rubber accordian like boot between the washer drum/tub and the drain pump,, another not too difficult fix, more of a pain in the rear, and its a common culprit in this type of washer) Well, it was not the problem this time, so I searched the internet, found this "door latch switch" gremlin coming up over and over. Didn't quite understand how this could be the issue, but, for under $30 I felt comfortable enough to give it a try before diving into costlier circuit boards, pumps, etc."
"And if you're even moderately mechanically inclined, you'll be ready to fix your own washer after watching a few YouTube videos."
"Our Affinity front load washer kept flashing the error code "dr" and beeping 4 times. THE TRICK that worked is: you have to break rule number one for working with electrical things and leave the power plugged in! The dr code will change to something like "18h" and the darn beeping will STOP."
"My only complaint is now there is a mechanical whine that builds up to a very annoying level until you push on the door."
"If your tumbler won't spin, this is most likely the culprit."
"After some youtube sleuthing, I found out you can simply remove the spring loaded metal ring on the front of the rubber seal, and with just two screws you can remove the front door latch assembly. You can pull the latch assembly through the opening you have created by pulling away the rubber seal (I admit I was nervous about doing this, but gosh, it was so darn easy, and if I can do this, you can too!)."