Best Furnace Replacement Fans
Backdraft dampers are simply fitted into the duct. Spring-loaded butterfly aluminum damper blades encased in a 20-guage galvanized steel housing. May be installed in any position or orientation to prevent backflow and designed for use in AC, Heating, Vent and other HVAC application temperatures from -22 to 180 degrees F (Fahrenheit).
Reviews
Find Best Price at Amazon"Seems to be good quality, easy to install, fitted perfectly in my 6 inch kitchen duct."
"Fit very snugly into our 6" stove top exhaust pipe and eliminated cold air seeping into our Kitchen."
"This damper was installed in a horizontal run and works flawlessly with a 50 cfm bathroom exhaust fan."
"I read about these and switched my kitchen and bath fans, the outside has just a screen, i removed the old plastic one with damper."
"Using it to prevent backdraft in a kitchen duct that used to get air from kitchen exhaust from below."
"Great product."
"I was trying to prevent negative pressure from pulling inside air up a draft vent."
"If you are looking for a high quality damper, don't look any further."
NEW- Fasco No.
Reviews
Find Best Price at Amazon"As described, fast shipping, as cheap as anywhere else."
"Fast shipping great product very happy."
"just what i need and shipped fast."
"PERFECT FACTORY REPLACEMENT FOR MY EMPYRE 450 WOOD BOILER."
Lopi Pioneer Bay Gas Convection Fan Blower 98900755a.
Reviews
Find Best Price at Amazon"The heater fan worked well and delivery was on time."
"It wasn't the USA made as advertised on the site."
"Part came faster than expected this close to Christmas which was great considering the cold front coming in."
"Fast shipping..... perfect fit...."
"Great item!"
"part had taken awhile to get."
Best Furnace Replacement Knobs
The Pull Handle is widely used for furniture, such as cabinet, drawer and so on. Hole Distance: 60 mm / 2.4''; Screw Size: 27 x 4 mm / 1.1'' x 0.16''(L*D).
Reviews
Find Best Price at Amazon"WOW."
Best Furnace Replacement Relays
This part replaces Rheem Ruud Weatherking part numbers 62-23543-01 and 62-23543-03. If this part fails within two years from date of purchase, return the defective part and a copy of the original invoice to the place of purchase for replacement. Direct Replacement Part For Many Rheem, Ruud, & Weatherking Furnaces.
Reviews
Find Best Price at Amazon"I watched the tech install the flame sensor, and it took him at most 4 minutes. I purchased this product, installed it in 5 minutes (very simple to do)."
"We decided to try a new sensor to avoid the repairmans yearly visit, and so far it works well."
"Needed a replacement flame sensor for my home heater and this was perfect."
"This is the exact same item as Rheem 62-23543-01 Flame Sensor Rod for Rheem, Ruud and Weatherking Furnaces which is half the price."
"Nothing fancy here, but I am happy to say that the flame sensor ceramics and metal end up sending the right signals (whatever those may be) to my RUUD natural gas furnace."
"Just replace it...it's not worth having a cold house when it is so easy to fix."
"This part was a direct replacement for the flame sensor in my 20 year old Rheem furnace."
"After repeatedly cleaning my old sensor, and having the short cycling prematurely wear out a relay on the control board, I replaced my old sensor with this one."
Best Furnace Replacement Cords
New 50 amp RV power cord adapter. Fits Marinco, Hubbel, Furrion 50 amp RV power inlets.
Reviews
Find Best Price at Amazon"If we are just stopping for a short while and only need a few accessories and the ability to charge the batteries this makes life a lot easier."
"works as it should but after twisting it in the 4 prongs does not let the cord hang at a 90 degree angel instead its at 8-9 oclock witch makes the weight of the cord you hook to it twist it back so its not locked in."
"Works great, extension cord plugs in easily."
Best Furnace Replacement Filters
The Lennox X6675 MERV 16 filter is a suitable replacement filter for the Lennox HCC20-28 air cleaner as well as many Honeywell, Carrier, and Trion Air Bear air cleaners that accept a 20" x 25" x 5" filter media. The Lennox X6675 filter is designed to fit the follow air cleaners: - Lennox: HCC20-16 - Honeywell: F25A1068, F25F1067, F35F1024, F100F1038, F150E1034, F200E1037 - Carrier: EZXCAB020, MACA020, MPKA020, FILCAB020 - Trion Air Bear: 453000-001, Supreme 2000, 455602-001, 447380-002 Features: - Suggested replacement for discontinued filter X5430 - Replacement filter for the Lennox HCC20-28 air cleaner - Carbon coated fiber matrix - Ozone and odor reduction capabilities - Industry's highest efficiency air filter - Removes particulates from the air stream. HCC20-28 (Cabinet) + HCF20-16 (Filter) 2000 cfm.
Reviews
Find Best Price at Amazon"did the Job / Affordable compared to what a service provider charges."
"Great product at a very good price."
"Price is excellent for OEM filter."
"Same product that we paid $130.00 for with the company that installed our furnace."
"The filters were packed very well and nice quality for my Lennox unit however the bottom filter had several areas of the carbon slats that had been smashed and for the cost I felt it should have been undamaged."
"If any high MERV rating filter is going to help your allergies and remove more particles, I would think and hope that this unique design with greater surface area (more folds) would be the best out there."
Best Furnace Replacement Motors
Furnace Flue Exhaust Blower 1/20hp, 3400 RPM 1.71 amps, 115 Volts Ball Bearings, Metal Housing Cross Reference Information: 70-24157-03, 70-22838-02, J238-150-1533, 70-101087-81, 70-101087-01, 70-24178-01, 70-24175-01, 70-24175-81, 7021-11559, 70-24157-03, 70-22838-02, 70-22838-82, Amtek 117104-01,117104-04, 117847-07, 66847, 66838, 117847-00, 7058-1406, a066. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"My existing unit started making a lot of noise, so I figured I had better replace it before it died on the coldest day of the year."
"I then looked on Amazon, found the exact match, read the reviews which bolstered my confidence in the part and my ability to make the change, and ordered it from MN Warehouse Deals."
"The new one is much heavier. Took me 15-20 minutes to install and I am not especially talented in repairs. Local repair company wanted $620 for this repair."
"You've heard the saying that dog won't hunt, well my furnace wouldn't run--after I deduced through trials and error via YouTube and other online venues-it's the stupid furnace inducer motor."
"A couple of things I had to do to make it work on my heater: Had to remove screws on top panel in order to get part in. The other thing is the old part's connectors for B&W power wires attach were on the top of the part, This new piece has the connectors on the bottom."
"The basket rusted out on the old unit."
"The Vent Safety Switch is not required on replacement induced draft blower motors."
"I don't think you would have a problem if your furnace is in a basement or remote room on the same level."
Best Furnace Replacement Ignitors
This part works with the following models: Frigidaire 30-2272-23/07, Frigidaire 30-3053-00-04, Frigidaire 30-3053-23-03, Frigidaire 30-3053-23-04, Frigidaire 30-3658-66-03. This part works with the following models: Frigidaire 30-2272-23/07, Frigidaire 30-3053-00-04.
Reviews
Find Best Price at Amazon"Then I got the electrolux from Sears which worked as it was essentially the same but it burned out after 3 months. Mine died Christmas eve with 10 family members visiting."
"If you are just tuning in this will be a short review … for the Frigidaire Gas Oven Ignitor 53039506. Then the bottom panel of oven, snipped the old ignitor wires, twisted on the new wires and installed wire nuts."
"3.2 to 3.6 amps for my stove."
"Great product so far, I just installed it today. The new igniter does not come with screws but that is no big deal if yours come out okay."
"My oven would only light by tapping the safety valve."
"The price was more than half off compared to the appliance repair store I was going to purchase it from."
"When purchasing from a local appliance repair store we paid $60.00 for the exact same part."
"The last time my oven would not heat up I paid an appliance repairman $315.00 to replace the igniter. Nine months after the last repair it was not heating up again. YouTube had a very easy video for just this very repair."
Best Furnace Replacement Heating Elements
Maximum flow rate 0.5 GPM (Gallons per Minute) = 45° F temperature rise.
Reviews
Find Best Price at Amazon"I first tested the water heater on LOW and ran water in the sink. The heater turned on and the water got mildly warmer (read, still cold), which I was expecting. Finally, I turned the heater on HIGH and the water from the faucet was too hot to keep my hands in it. Because I knew that not enough flow would cause the heater to turn off, because it requires 0.5GPM to activate, I had the shower turned all the way up with a 2.5GPM shower head. I thought that the problem could be not enough flow but not because it wasn't reaching the 0.5GPM but because it was not getting enough water through the heater to keep it from overheating and causing the heat protection system to shut off the heater. Because of this, I'll be testing out running the heater on Medium to see if it gets the water hot enough for a shower. Of course, some will say that it could still be that there was not enough water flow but if that was the case then the heater should just turn off and not come back on. This means that the flow rate of your water system is going to change as the pressure changes and this translates to corresponding water temperature changes. The water heater overheat protection will turn off the water heater when operating on the High setting if there is not enough flow. The point I'm trying to make is that unless you can make your own temperature controller, you might want to consider a different model, unless you don't mind cold water during your shower."
"Really works great hot water instant."
"Easy, fast installation, does the job I wanted on medium setting."
"Ive had these before but this one doesnt seem to be working I think its just a fluke."
"Small and easy to install!"
"Doesn't heat water; just slightly warms it."
Best Furnace Replacement Circuit Boards
This is a Genuine Replacement Part ,The Model Number and Name for the Following Item: SLT50 Ignition Control Module. Manufacturer: White Rodgers.
Reviews
Find Best Price at Amazon"It also has options for running the indoor fan motor after the outside unit turns off to use the remaining cold or hot air in the ducts to condition the building. I only needed to jump one wire which was explained in the instructions if you have a heating system that does not support a flame burnout detector sensor."
"Later I spent a few hours trying everything, when the furnace was not working at all, simply because I had not noticed a safeguard button, the furnace or fan can not work without me or the panels pressing such button (the furnace will not work when it is open). finally make sure you know how to operate the furnace with open panels before starting."
"Then mounted the new unit and transferred the wires one-by-one. The only challenge to my technique was that once the new unit was mounted, it can be tough to get your eyes close to it to see the labels on the wire connections, but that may still be better than connecting the wires first and then trying to mount the unit."
"Worked great on my furnace!!"
"Purchased this control board to replace a 50A55-288."
"It included extra extensions for wires that didn't reach the new connections."
"I installed myself by unplugging one line at a time to insure proper plug in on new control panel."
"Replaced my 50A50-241 and it was a direct fit without any jumpers or cables needed."
Best Furnace Humidifiers
The TrueEASE Humidifier Line is easy to install with quick snap bypass direction adjustment.
Reviews
Find Best Price at Amazon"I have a high efficiency Bryant furnace with a GEO thermo system and needed a way to increase the humidity in the house in the cold Minnesota winters."
"I am able to increase the humidity by 1% per hour in a 3700 sq ft two story plus finished basement home. The installation was straight forward with the exception of setting the dip pin switches for my existing Honeywell VisionPRO IAQ thermostat."
"eyeontheprize's review is the only place that I found the information on the significance of using a hot water supply instead of cold to the unit. The manual says to use either cold or hot water, but it does not say anything about the humidification performance between selecting cold or hot water. I initially installed the HE300A1005 with a cold water supply, since I had a cold water line near the unit. My well water system supplies 55-degree cold water, so changing to the hot water made an 80-degree difference (my hot water is set at 135-degrees). I also have a heat pump hot water tank so the cost of hot water is significantly lower than an non-heat pump electric or gas hot water tank. Just make sure you understand that the installation considerations of providing warm air and hot water to the unit will significantly affect the performance of the unit. Update - So, after a while the humidifier Pad gets clogged and the water starts running out of the bottom of the unit."
"I installed it my self with no problems. I don't feel the 4 hour install was to much time. I feel I did a good neat job on it, no problems all winter, good results with the dry air problem."